Study Guides and Actual Real Exam Questions For Oracle OCP, MCSE, MCSA, CCNA, CompTIA


Advertise

Submit Braindumps

Forum

Tell A Friend

    Contact Us

 Home

 Search

Latest Brain Dumps

 BrainDump List

 Certifications Dumps

 Microsoft

 CompTIA

 Oracle

  Cisco
  CIW
  Novell
  Linux
  Sun
  Certs Notes
  How-Tos & Practices 
  Free Online Demos
  Free Online Quizzes
  Free Study Guides
  Free Online Sims
  Material Submission
  Test Vouchers
  Users Submissions
  Site Links
  Submit Site

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Online Training Demos and Learning Tutorials for Windows XP, 2000, 2003.

 

 

 

 





Braindumps for "JN0-360" Exam

Certified Internet Specialist, –Service Provider (JNCIS-SP)

 Question 1.
What are two valid actions that can be applied to a frame by a Layer 2 firewall filter? (Choose two)

A. Log
B. loss-priority
C. sample
D. count

Answer: B, D

Explanation:
The correct answers are B, D.
Reference:
You can specify the following filter actions:
* accept
* count counter-name
* discard
* dscp code-point (family inet only)
* forwarding-class class-name
* ipsec-sa ipsec-sa (family inet only)
* load-balance group-name (family inet only)
* log (family inet and inet6 only)
* logical-system logical-system-name (family inet and inet6 only)
* loss-priority (high | medium-high | medium-low | low)
* next term
* next-hop-group group-name (family inet only)
* policer policer-name
* port-mirror (family bridge, ccc, inet, inet6, and vpls only)
* prefix-action action-name (family inet only)
* reject  (family inet and inet6 only)
* routing-instance routing-instance-name (family inet and inet6 only)
* sample (family inet, inet6, and mpls only)
* service-accounting (service filters and family inet or inet6 only)
* service-filter-hit (service filters and family inet or inet6 only)
* syslog (family inet and inet6 only)
* three-color-policer policer-name
* topology topology-name (family inet and inet6 only)
* traffic-class code-point (family inet6) only

Question 2.
Which two statements describe differences between IPv4 and IPv6? (Choose two)

A. IPsec is built into IPv6
B. IPv6 uses a 32-bit (4-byte) address and can support up to 4,294,967,296 addresses
C. IPv4 supports extension headers whereas IPv6 options are integrated into the base
D. IPv6 eliminates the need for NAT

Answer: A, D

Explanation:

Question 3.
You must configure an OSPF area that does not accept type 3 link-state advertisements (LSAs) from area 0 (other than the default route) You have configured your area to be stub, but you still see type 3 LSAs.

What will account for this behavior?

A. You should have configured your area as totally stubby
B. You should have used a not-so-stubby-area
C. You are experiencing a routing loop
D. You have exported routes into OSPF

Answer: A

Explanation:

Question 4.
You have configured an IP-IP tunnel between Router A and Router B

Which Junos operational mode command is used to verify that the tunnel interface is up and operational?

A. show chassis tunnel status
B. show tunnel interface
C. show interfaces terse
D. show interfaces tunnel

Answer: C

Explanation:

Question 5,
Which IS-IS packet is used to determine the level of an IS-IS neighbor?

A. IIH
B. LSP
C. PSNP
D. CSNP

Answer: A

Explanation:

Question 6.
Router A is an OSPF router connected to both Area 0 and Area 1 Area 1 has been configured as a stub area 

Which two LSA types does Router A suppress from Area 1 ?

A. Router LSA
B. External LSA
C. Summary LSA
D. ASBR Summary LSA

Answer: B, D

Explanation:

Question 7.
You are logged into a router and have navigated to the (edit routing-options] level of the hierarchy. You have been asked to create a static route that will use 10.10.10.1 as its primary next-hop and 10.10.10.5 as its secondary next-hop.

Which command correctly configures this scenario?

A. set static route 8/8 10.10.10.1 qualified-next-hop 10.10.10.5 pref 10
B. set static route 8/8 next-hop 10.10.10.1 secondary-next-hop 10.10.10.5 preference 10
C. set static route 8/8 next-hop 10.10.10.1 qualified-next-hop 10.10.10.5 preference 10
D. set static route 8/8 next-hop [10.10.10.1 10.10.10.5] pref 10

Answer: C

Explanation:

Question 8.
Which Junos operational mode command is used to verify that load balancing is working as expected?

A. show route all
B. show route extensive
C. show route balancing
D. show route forwarding-table

Answer: D

Explanation:

Question 9.
Click the Exhibit button

Based on the illustration of the VPLS topology shown in the exhibit, which statement is true?

A. PE-C must have a spanning-tree protocol enabled
B. CE-C must have BGP enabled
C. Traffic forwarded from PE-C to PE-A is forwarded on to PE-B
D. Traffic forwarded from PE-C to PE-A is not forwarded on to PE-B

Answer: D

Explanation:

Question 10.
Which two values displayed in the output from the show spanning-tree MSTP configuration command must match on all switches participating in the same MSTP region? (Choose two)

A. root bridge identifier
B. authentication checksum
C. context identifier
D. configuration digest

Answer: C, D

Explanation:

Question 11.
Which role does the router ID (RID) have in the BGP route selection process?

A. The router ID is evaluated immediately after MED to determine route preference
B. The router ID is evaluated last in the route selection process
C. The router ID is evaluated after the cluster length and a lower router ID is chosen
D. The router ID is evaluated after analyzing the IGP metric cost

Answer: C

Reference:
http://www.juniper.net/techpubs/en_US/junos10.0/information-products/topic-collections/nogbaseline/bgp-routes-and-selection-introduction.html



Google
 
Web www.certsbraindumps.com


Study Guides and Real Exam Questions For Oracle OCP, MCSE, MCSA, CCNA, CompTIA





              Privacy Policy                   Disclaimer                    Feedback                    Term & Conditions

www.helpline4IT.com

ITCertKeys.com

Copyright © 2004 CertsBraindumps.com Inc. All rights reserved.