Question 1.
Which SAN extension topology is a low-latency, cost-effective, high-bandwidth solution that is suitable only within a limited geographical area?

A. FCIP
B. DWDM
C. CWDM
D. SONET/SDH

Answer: C

Question 2.
Your Cisco MDS 9509 configuration requires 2000 watts of power and is configured with two 2500W power supplies. 

If 110V power is provided to the switch, in which power mode does the switch operate?

A. The director will operate in redundant mode only.
B. The director will operate in combined mode only
C. The director will operate in redundant mode or combined mode
D. The director cannot operate with 110V power

Answer: B

Question 3.
Which two kinds of applications require sustained throughput and are sensitive to latency? (Choose two.)

A. synchronous replication
B. asynchronous replication
C. OLTP
D. tape backup
E.
F. mail

Answer: A, D

Question 4.
Which of the following designs would provide your customer with the highest performance and port utilization?

A. multi-tier design
B. collapsed core design
C. core.edge design
D. single.tier design

Answer: B

Question 5.
Refer to the exhibit.
 
A customer plans to add a tape backup subsystem to its existing storage network. 

In which location should the customer place the tape backup device in order to provide the best performance during backup and recovery?

A. A
B. B
C. C
D. D

Answer: B

Question 6.
Refer to the exhibit.
 

You are designing a new SAN. The existing SAN uses eight 32-port 2-Gbps Fibre Channel switches. Two of the switches are deployed as core switches, and the remaining six switches are deployed as edge switches. Each edge switch has two ISLs to each of the two core switches. The disk array has twelve 2-Gbps Fibre Channel ports. Each of the 84 servers has a dual-port 1-Gbps Fibre Channel HBA.

Which Cisco MDS 9000 configuration would improve performance?

A. two Cisco MDS 9216 switches, with two 48-port Fibre Channel line cards in each switch
B. two Cisco MDS 9506 switches, with three 32-port Fibre Channel line cards in each switch
C. two Cisco MDS 9506 switches, with one 16-port Fibre Channel line card and two 48-port Fibre Channel line cards in each switch
D. two Cisco MDS 9513 switches, with two 48-port Fibre Channel line cards in each switch

Answer: C

Question 7.
How does RolE.Based Access Control (RBAC) enhance manageability in an environment with VSANs?

A. limits operator errors by isolating user management domains within a large physical infrastructure
B. specifies port membership to a specific VSAN
C. configures security options for host ports that are assigned to a VSAN
D. configures VSAN membership for specific trunk ports

Answer: A

Question 8.
Which three of these Cisco storage and networking devices are optimized for use in FCIP SAN Extension implementations? (Choose three.

A. MDS 92161 Multilayer Fabric Switch
B. IPS-8
C. MDS 9120 Multilayer Fabric Switch
D. MDS 9140 Multilayer Fabric Switch
E. MPS-14/2
F. ssm

Answer: A, B, E

Question 9.
Which statement is true concerning the Cisco MDS switch when operating in native interop mode?

A. The MDS switch can interoperate with Non-MDS switches that are certified by SNIA.
B. The MDS switch can interoperate with Non-MDS switches that support "MDS Native" mode.
C. The MDS switch can interoperate with Non-MDS switches that properly adhere to 
    FibreChannel switch standards.
D. The MDS switch cannot interoperate with Non-MDS switches.

Answer: C

Question 10.
Which two items are necessary when implementing a highly available SAN design? (Choose two.)

A. redundant hardware
B. localized data backups
C. real-time fabric monitoring
D. nondisruptive upgrades
E. traffic engineering and QoS

Answer: A, D

	Web www.certsbraindumps.com