Question 1.
What command would be entered to restart VSAN 100?

A. no vsan 100 start vsan 100 start
B. no vsan 100 resume vsan 100 resume
C. vsan 100 restart non-disruptive
D. vsan 100 restart disruptive
E. vsan 100 suspend no vsan 100 suspend

Answer: E

Explanation:
VSAN restart: vsan 100 suspended, no vsan 100 suspended

Question 2.
Persistent binding is:

A. binding an IP address to a NIC card and target ID number
B. Binding WWN of an initiator to a target port and target ID
C. Binding PWWN of an initiator to a target port Pwwn AND A TARGET id NUMBER
D. Binding target WWPNpWWN to an initiator instance and target ID number
E. Binding target Nwwn TO AN INITIATOR INSTANCE AND TARGET id NUMBER

Answer: B

Explanation:
Persistent binding.

Question 3.
What is used for in-band management of MDS switches?

A. FCIP
B. IP over Ethernet
C. IPFC
D. DNS
E. VRRP

Answer: C

Explanation:
Inband management: IPFC

Question 4.
AAA(TACACS+Radius) protocols can be used to authentication and/or authorize what on MDS?

A. Telnet and Console access
B. SSH
C. RBAC
D. Dhchap for fabric security
E. All the above

Answer: E

Explanation:
AAA can be used for Telnet, console, SSH, RBAC, DHCHAP

Question 5.
Network Data Management Protocol is used primarily for:

A. Coordinating hierarchical storage management
B. Mirroring file systems between disk subsystems over an IP network
C. Backing up Network Attached Storage devices
D. Synchronizing databases between multiple vendors
E. A common protocol and API to provision storage for different subsystem vendors

Answer: C

Explanation:
NDMP for NAS backup

Question 6.
Exhibit:
In the above picture, switch 3 and switch 5 are not IVR capable switches. All the ISLs are 1 GB links. Switches 2,4 and 6 are IVR-capable switches. 

What is the FSPF costs from Switch 1 to reach Points 1,2, and 3?

A. 501.1502.2502
B. 1001.30025002
C. 501.1503.2505
D. 1000.3000.5000
E. 500.1500.2500

Answer: B

Explanation:
IVR with FSPF cost

Question 7.
During an E-port initialization, what internal link service is used to exchange Link Parameters and the operating environment of the two interconnecting ports as well as the capabilities of the switches connected by them?

A. EFP
B. FLOGI
C. PLOGI
D. ELP
E. SW_RSCN

Answer: A

Explanation:
EFP: Exchange Fabric Parameter

Question 8.
What load balancing option should best utilize all available ISLs on port Channel?

A. Flow Based
B. Source FCID based
C. Frame based
D. Source/Destination FCID Exchange based
E. Source and Destination FCID based

Answer: D

Explanation:
Best load balancing utilization

Question 9.
When using IVR traversing a FCIP link, what is not required?

A. Transit VSAN over FCIP link
B. Two or more VSANs in configuration
C. IVZ active for host to access storage
D. Border switch will be member of at least two VSANs

Answer: A

Question 10.
What does MDS FC-SP functionality mode “auto-active” represent?

A. Port will initiate FC-SP authentication after ESC.
B. Port will actively listen, but will not initiate authentication
C. Port will successfully complete FC-SP authentication only if remote end is in passive mode
D. Port will initiate FC-SP authentication with TACACS server as default
E. Port will use default of no authentication.

Answer: A

Explanation:
FC-SP auto-active: after ESC, it will initiate FC-SP authentication

	Web www.certsbraindumps.com