|
Question 1.
What is Forwarding Equivalence Class assignment NOT likely to be based upon?
A. Fragment offset
B. Destination address
C. Application protocol
D. Class of service
Answer: A
Question 2.
For communications systems what describes the over-all health of the system?
A. Bit-Error-Rate (BER)
B. Synchronous Optical Network (SONET)
C. Optical Signal to Noise Ratio (OSNR)
D. None of the above
Answer: A
Question 3.
In MPLS what is an LSP?
A. Label Selection Pair
B. Label Switched Path
C. Lightweight Signaling Protocol
D. Large Sampling Path
Answer: B
Question 4.
CIDR is primarily used:
A. In BGP only
B. For classless routing
C. In OSPF only
D. In EIGRP only
Answer: B
Question 5.
What type of fiber-optic system is used to distribute cable television signals?
A. Point to multipoint
B. Local Area network
C. Switched
D. Point to point
Answer: A
Question 6.
You work as a network administrator at Company.com. Study the exhibit carefully.
Upon deleting an IOS image file from flash, an execution of show flash shows the file still in flash, with a 'D' preceding it (as shown in the exhibit). What step must be taken in order to remove the file completely?
A. Erase the file from flash
B. Format the flash device
C. Replace the flash card - it is defective
D. Execute a squeeze command on the flash device
Answer: D
Question 7.
What does NOT contribute to lowered throughput in practical IP over ATM networks?
A. ILMI overhead
B. SAR delay
C. Cell tax
D. Cell padding
Answer: A
Question 8.
The TCP PUSH flag indicates:
A. The data in the TCP receive buffer should be sent to the application listening to this TCP
connection without waiting for further data.
B. Any data being buffered by routers between the source and destination for this connection
should be sent immediately.
C. The sender should make certain its send buffer is pushed onto the wire.
D. This session is about to end.
Answer: A
Question 9.
What is the difference between pre-positioned and pre-loaded content in an ACNS 5.X Content Delivery Network?
A. Pre-loaded content is content that has been fetched by the root Content Engine and distributed
to all the Content Engines.
Pre-positioned content is content that all Content Engines fetch independently from an origin
server.
B. Pre-loaded content is content that has been fetched by the Content Distribution Manager
distributed to all the Content Engines. Pre-positioned content is content that all Content
Engines fetch independently from an origin server.
C. Pre-positioned content is content that has been fetched by the root Content Engine and
distributed to all the Content Engines.
Pre-loaded content is content that all Content Engines fetch independently from an origin
server.
D. Both are exactly the same and do the same function.
E. Pre-positioned content is content that has been fetched by the Content Distribution Manager
and distributed to all the Content Engines. Pre-loaded content is content that all Content
Engines fetch independently from an origin server.
Answer: C
Question 10.
What is the WCCP Service Group number for Reverse Proxy?
A. 80
B. 90
C. 82
D. 99
E. 0
Answer: D
|
Question 1.
What does the linkloop command test?
A. router activity
B. Maximum Transmission Unit (MTU) size
C. MAC address connectivity between network cards
D. loopback address connectivity between network cards
Answer: C
Question 2.
Which file contains the information sent in response to a bootp request?
A. /etc/services
B. /etc/bootptab
C. /etc/inetd.conf
D. /etc/bootp.conf
Answer: B
Question 3.
Which commands can confirm host name resolution (DNS/Bind) is working correctly?
A. whois
B. uname
C. nsquery
D. hostname
E. gethostbyname
Answer: C
Question 4.
What is IP multiplexing on a UNIX host?
A. increasing throughput on the network interface
B. binding the same IP address to multiple network interface
C. binding more than one IP address to a single network interface
D. binding more than one MAC address to a single network interface
Answer: C
Question 5.
Which tools have been deprecated with the introduction of the nwmgr command? (Select three.)
A. netstat
B. ifconfig
C. linkloop
D. lanscan
E. lanadmin
Answer: C, D, E
Question 6.
How can you enable only NFS version 4 support on HP-UX 11i v3?
A. HP-UX v3 does not support NFSv4.
B. Change the NFSv4 kernel parameter to yes, recompile the kernel and reboot.
C. Using only NFSv4 is not supported; NFSv2 and NFSv3 are always enabled.
D. Set the configuration parameters NFS_SERVER_VERSMIN and NFS_SERVER_VERSMAX
to 4.
Answer: D
Question 7.
Which NFS server file contains a list of clients that currently have the server's NFS file systems mounted?
A. /etc/fstab
B. /etc/rmtab
C. /etc/nfstab
D. /etc/mnttab
E. /etc/exports
Answer: B
Question 8.
What is the length of an IPv4 address?
A. 32 bits
B. 48 bits
C. 64 bits
D. 128 bits
Answer: A
Question 9.
What are the major features of IPFilter on HP-UX 11i v3? (Select three.)
A. creates extensive logs
B. supports X.25 Interfaces
C. installed and enabled by default
D. provides a new GUI configuration tool
E. supports Network Address Translation (NAT)
Answer: A, B, E
Question 10.
Which command displays Internet to Ethernet address resolution?
A. arp
B. lanscan
C. ifconfig
D. traceroute
Answer: A
Copyright © 2004 CertsBraindumps.com Inc. All rights reserved.