|
Question 1.
ITCertKeys .com wants to deploy the Cisco Business Ready Teleworker solution, but is currently using a traditional (non-IP) PBX for voice services.
What would you recommend to this customer?
A. Deployment of Business Ready Teleworker with VoIP is not recommended.
B. The customer's existing PBX must first be replaced with Cisco IP Telephony solution.
C. Business Ready Teleworker and Cisco IP Telephony can be deployed in parallel to the
existing PBX, integrating the two with trunking.
D. Deployment is recommended only for full-time Teleworkers who have no other corporate
phone.
Answer: C
Question 2.
When is an IPSec SA built on the Teleworker Router?
A. when the router is booted up
B. when the router administratively does a no shutdown" on the IPSec SA
C. when traffic matches a line of the access-list tied into the crypto-map in the router
configuration, and that particular IPSec SA is not already up
D. when the ISAKMP SA completes negotiation of all IPSec SAs (one per access-list line in the
crypto ACL), it will be brought up immediately
Answer: C
Question 3.
What characteristics make ADSL the likely choice among DSL technologies for Teleworker? Choose two.
A. most widely deployed by service providers
B. provides asymmetrical bandwidth, including high speed downlink
C. data rate is affected by distance to the Central Office
D. provides the furthest reach at T1 speeds
E. supports connection of two routers without the use of a DSL access concentrator
Answer: D, E
Question 4.
When IP Telephony is deployed for Teleworkers using the Cisco Business Ready Teleworker solution, which statements are true? Choose two.
A. There is lower bandwidth consumption for VoIP media streams.
B. Teleworkers can have the same extensions and inward-dialing numbers at their office desks
and home offices.
C. Personal calls are routed directly through the residential PSTN line.
D. Teleworkers can have different extensions at their office desks and home offices.
E. There is less burden on Cisco Call Manager for signaling traffic.
F. Incoming calls are first routed to the office desks, then to the home offices.
Answer: B, D
Question 5.
An Enterprise decides to implement Authentication Proxy for per-user authentication for home offices. Each home office also supports an IP Phone.
What should you do?
A. Configure Access Control Lists to ensure Voice over IP traffic is checked by Auth Proxy.
B. Configure pNAT to ensure Voice over IP packets are properly translated.
C. Configure IOS firewall to permit RTP port numbers through the firewall via VPN.
D. Configure Access Control Lists to allow Voice over IP traffic to bypass Auth Proxy checking.
Answer: D
Question 6.
An Enterprise customer is concerned about the effort involved in allocating remote network addressing at the Teleworker location.
What should you recommend to the customer?
A. Cisco Works VPN Manager
B. Easy VPN client mode
C. deploy Linksys routers with menu driven configuration
D. disable 802.1x and Auth Proxy on the Teleworker router
Answer: B
Question 7.
ITCertKeys .com indicates they run a mission-critical application which marks its packets best-effort (DSCP=0).
How can you guarantee delivery of this traffic?
A. Remark the traffic on ingress and prioritize on egress.
B. Enable CEF and Net flow.
C. Configure the MS-Windows QoS Scheduler to prioritize this traffic.
D. Enable WRED.
Answer: A
Question 8.
When is it appropriate to enable Link Fragmentation and Interleaving (LFI) on DSL connections for Teleworkers? Choose three.
A. uplink speed less than 768kbps
B. supporting Voice-over-IP
C. using PPPoE encapsulation
D. using PPPoA encapsulation
E. uplink speed greater than 768kbps
Answer: A, B, D
Question 9.
Which is not a reason that Internet Service Providers prefer to use PPP over Ethernet (PPoE)?
A. access control and billing can be done on a per-user, rather than a per-site basis
B. supports Link Fragmentation and Interleaving
C. provides the ability to connect a network of hosts over a simple bridging access device
D. provides a consistent means of authenticating users (RADIUS for example)
Answer: B
|
Question 1.
Which three are contained in the Safety Plans application? (Choose three.)
A. Job Plan
B. Hazard(s)
C. Attached Documents
D. Equipment or Location
E. Condition Monitoring Point
Answer: B, C, D
Question 2.
Which two types of locations can be created in MAXIMO's Location application? (Choose two.)
A. Repair
B. Salvage
C. Equipment
D. Work Order
Answer: A, B
Question 3.
Which three steps are involved in transferring an item between storerooms using the Issues and Transfers application? (Choose three.)
A. select items for transfer
B. perform a Transfer In transaction
C. perform a Transfer Out transaction
D. perform a material receipt to the storeroom
E. select the Work Order, Location, or GL Account code
Answer: A, B, C
Question 4.
How should you create a Primary System in the Locations application?
A. It is created automatically.
B. enter it in to the System area
C. use the System toolbar button
D. click Select Action | Manage Systems
Answer: D
Question 5.
Which two fields are required on the Preventive Maintenance (PM) main screen to generate a Work Order? (Choose two.)
A. Route
B. Supervisor
C. Next Job Plan
D. Work Order Status
E. Location, Equipment, or GL Account
Answer: D, E
Question 6.
What are three steps for entering Problem, Cause, and Remedy Codes on a Work Order? (Choose three.)
A. click the Failure Reporting tab and enter the codes
B. enter Problem, Cause, and Remedy Codes on the Work Order main tab
C. enter the Failure Class and Problem Code on the Work Order main screen, click the Failure
Reporting tab, and enter the Cause and Remedy Codes
D. if the Failure Class is present, enter the Problem Code on the Work Order main screen, click
the Failure Reporting tab, and enter the Cause and Remedy Codes
Answer: A, C, D
Question 7.
Which application is used to modify delivered MAXIMO reports?
A. BRIO Workbench
B. Actuate ReportCast
C. eReport Designer Professional
D. Actuate Administrative Desktop tool
Answer: C
Question 8.
Which application can move equipment to another location or equipment parent?
A. Inventory
B. Equipment
C. Work Request
D. Issues and Transfers
Answer: B
Question 9
Which three data elements does the Equipment record store? (Choose three.)
A. serial number
B. model number
C. installation date
D. replacement date
Answer: A, B, C
Question 10.
What is the best action to create a Work Order when additional work is required?
A. select the Work Order in question;
click Select Action | Duplicate Work Order
B. select the Work Order in question;
click Select Action | Generate Follow-up Work
C. select the Work Order in question;
write down the Work Order number;
click the New Work Order icon;
write in the original Work Order number in the Originating WO field
D. select the Work Order in question;
go to the Work Order field and copy the Work Order number;
click Select Action | Duplicate Work Order;
copy the original Work Order number in the Originating WO field
Answer: B
Copyright © 2004 CertsBraindumps.com Inc. All rights reserved.