|
Question 1.
The CE starts the distribution of the code across all nodes by issuing the command "install file:///tmp/2.4.1-834-592-11742.tgz".
Which command should the CE use to monitor the distribution?
A. Show activation
B. Show upgrade status
C. Show cluster status
D. Show config version
Answer: D
Question 2.
When CPP is enabled, how is the data stored?
A. Blob Mirrored, CDF spread out over 6 disks
B. CDF mirrored, Blob spread out over 7 disks
C. CDF mirrored, Blob spread out over 6 nodes
D. CDF mirrored, Blob Mirrored
Answer: C
Question 3.
The CE is having a problem installing a CUA on a Gen2 node.
What could be the problem?
A. Port that node is connected to on the Cube switch is disabled
B. Gen2 does not support CUA
C. Corrupted bin file
D. Centera viewer does not have the latest ServiceExt.jar
Answer: B
Question 4.
When the cluster is locked, which service functions are disabled?
A. Modem, email home
B. SMTP, Replication
C. CPP, CPM
D. CLI/CV/SSH
Answer: D
Question 5.
Orphans in a CFA environment are files deleted from which platform?
A. Centera but NOT the Celerra
B. Celerra but NOT the Centera
C. CFA but NOT from the Centera
D. Celerra but NOT from the CFA
Answer: B
Question 6.
The Centera Access Nodes have the capability to auto-negotiate. What is auto-negotiate?
A. Poll the attached device to determine whether it is running synchronous or asynchronous and
match its settings
B. Determine the best possible route to communicate with the destination device by polling the
surrounding network
C. Scanning the network environment to determine what type of network characteristics are
configured
D. Determine the transmission speed and duplex setting of the attached device and match its
characteristics
Answer: D
Question 7.
Which socket port needs to be open so that API can connect to an access node?
A. 3682
B. 3200
C. 3218
D. 3210
Answer: C
Question 8.
Replication has an autopause feature to automatically pause the replication process.
Which criteria would cause replication to be automatically paused?
A. Remote cluster is 75% full
B. 1000 clips in the parking queue
C. Application profile mismatch
D. 50,000 clips in the replication queue
Answer: C
Question 9.
What is the purpose of Kickstart?
A. Adds an additional cabinet
B. Initializes the internal network
C. Assigns cube functionality
D. Initializes the call home function to EMC support
Answer: B
Question 10.
To setup Centera File Archiver in addition to Centera and CUA, which hardware is required?
A. Legato Server
B. Symmetrix
C. CLARiiON
D. Celerra
Answer: D
Question 11.
Which minimum code is required to monitor Centera from the EMC Control Center?
A. 3.0
B. 2.4
C. 2.2
D. 2.3
Answer: D
Question 12.
A CE is out in the field doing a Gen4 install, and notices that there are too many or too few nodes.
What are the possible node configurations for a single Gen4 cube?
A. 4, 8, 12, 16
B. 8, 12, 16, 32
C. 8, 12, 16, 24
D. 4, 8, 16, 32
Answer: A
Question 13.
Which utility is recommended to copy CentraStar code to a node?
A. ftp
B. pscp
C. copy
D. tftp
Answer: B
Question 14.
In the Star Replication topology, what is the ratio of edge clusters to core clusters?
A. 3 to 2
B. 2 to 1
C. 1 to 2
D. 3 to 1
Answer: D
Question 15.
What is the proper way to soft boot a Gen3 node?
A. Use the reset switch
B. Use the front panel button
C. Power down the node
D. Use the CLI
Answer: B
Question 16.
How many CUAs can point to the same Centera?
A. 2
B. 1
C. 6
D. Unlimited
Answer: A
Question 17.
The CE has replaced a node in a Centera Cluster. When the node shows up in Centera Viewer, it is offline.
What is the problem with the replacement node?
A. Network cables are mis-wired
B. Wrong CentraStar version
C. Wrong generation hardware
D. Defective disks installed
Answer: B
|
Question 1. Which port is indicated on the right Secondary Codec for the CTS-3210? A. Right Display B. Right Camera C. Center Display D. Left Display Answer: B Explanation: Question 2. Which port do you conned to on the Primary Codec in order to establish an Ethernet connection between your laptop and the Cisco TelePresence 3000 equipment? A. Video port B. Network port C. IP Phone port D. Secondary Camera port Answer: B Explanation: Question 3. Which size and type of tool is required to loosen the screws that allow rotational adjustment of the CTS-3010 cameras? A. #1 Phillips screwdriver B. 5.0 mm Allen wrench C. #3 Phillips screwdriver D. 3.0 mm Allen wrench Answer: D Explanation: Question 4. Which four functions does Cisco TelePresence rely on Cisco Unified Communications Manager for? (Choose four) A. Configurations B. Software upgrades C. Management D. Call processing E. Scheduling meetings F. Microphone calibration Answer: A, C, D, E Explanation: Question 5. Which three of the following components are included on the Cisco TelePresence 3210? (Choose three.) A. One boardroom-style table with a second row B. One boardroom-style table C. One 40" external display D. Nine table microphones E. Four LED light fixtures Answer: A, C, D Explanation: Question 6. DRAG DROP Answer: Explanation: Layer 2 Datalink – ARP Layer 3 – Network – IP Layer4 – Transport – TCP Layer7 – Application - Email Question 7. Which three of the following are benefits of Cisco TelePresence Manager? (Choose three) A. Bulk software upgrades of endpoints B. Calendaring integration and management C. One-Button-to-Push meeting access D. Allow for content sharing E. Concierge services Answer: B, C, D Explanation: Question 8. Which two hardware components are optional for the Cisco TelePresence 1000? (Choose two) A. One Cisco Unified IP Phone 7975G B. One external display C. One high-definition camera D. One Auxiliary Control Unit Answer: A, D Explanation: Question 9. Which port is indicated on the Auxiliary Control Unit for the CTS-1100 and 1300? A. Auxiliary Collaboration Display B. Serial Control for Projector C. Lights D. Serial Control for Dimmer Box Answer: B Explanation: Question 10. DRAG DROP Answer: Explanation: CTS-500 – 1-2 participants in a home/executive office CTS-1100 – 2 participants in multipurpose room CTS-1300 – 6 participants in multipurpose room CTS-3010 – 6 participants in dedicated telepresence room CTS-3210 – up to 10 participants in dedicated telepresence room
Copyright © 2004 CertsBraindumps.com Inc. All rights reserved.