|
Question 1.
Just prior to starting a raw backup of a disk partition to ensure data integrity, you must.
A. run the performance test
B. check the disk capacity
C. unmount the disk
D. check the disk data integrity test
Answer: C
Question 2.
On a Solaris system, how does the jbconfig command prompt for tape drive information?
A. from the lowest number to the highest in /dev/rmt
B. from the lowest SCSI target number to the highest
C. from the highest SCSI target number to the lowest
D. from the lowest numbered device element to the highest
Answer: D
Question 3.
Which Net Worker level will produce a backup of ITCertKeys.com's Microsoft Exchange Transaction logs only, without truncating them afterwards?
A. Incremental
B. Level 1 Differential
C. Consolidate
D. Full
Answer: B
Question 4.
Exhibit:
For the configuration shown in the exhibit, what will ensure that the Microsoft Windows client can recover data even if storage node A is down?
A. adding storage node B hostname to the Clone Storage Node attribute of the Microsoft
Windows Client resource
B. adding storage node B hostname to the Clone Storage Node attribute of the Net Worker
server's Client resource
C. adding storage node B hostname to the Read Hostname attribute of the Microsoft Windows
Client resource
D. adding storage node B hostname to the Read Hostname attribute of the Jukebox resource
Answer: D
Question 5.
What is the Net Worker server often referred to as, in an NDMP Version 3 or 4 solution?
A. The Data Service Provider (DSP).
B. The NDMP Data Server.
C. The NDMP Client.
D. The Data Management Application (DMA).
Answer: D
Question 6.
ITCertKeys.com deploys a new Windows 2003 Server in their environment and want to do Microsoft Volume Shadow Copy Service (VSS) backups using Net Worker. VSS is started, and it is enabled on the shared volume. However, you are still unable to see VSS save sets in the winworkr GUI.
What is a likely reason for this happening?
A. You did not reboot Windows 2003 after enabling VSS.
B. You need to restart the VSS Service after enabling VSS.
C. You have not installed the VSS Enabler on Net Worker.
D. You have not installed the VSS Module for Net Worker.
Answer: C
Question 7.
A value of 0 (zero) for the Save Lockout attribute indicates that.
A. the storage node will not be locked from receiving save assignments
B. the save-mount timeout value is set to 0 (zero)
C. no save sets can be sent to this device
D. the storage node will be indefinitely locked from receiving save assignments
Answer: A
Question 8.
Microsoft Exchange 2000 supports which two of the following levels of Net Worker backup? (Choose two.)
A. level 0
B. level 5
C. level 9
D. level 1
Answer: A, D
Question 9.
For what reason is having as few save groups as possible running, generally a good idea?
A. Each group uses its own processing time and disk space.
B. Each group uses its parallelism.
C. Each group uses its own logging mechanism, which results in multiple log files.
D. Each group uses its own processing time and memory.
Answer: D
Question 10.
You are a backup operator for ITCertKeys.com. ITCertKeys.com asks you to move a DLT7000 tape drive from their Net Worker server to a client for the purpose of backing up the files locally. Unfortunately, this attempt at improving the backup speed fails.
Of the following, which two are reasons for the backup speed not improving? (Choose two.)
A. You have forgotten to enable software compression for that client.
B. You have forgotten to adjust the Storage Node List for that client.
C. The Net Worker client is unable to deliver the data fast enough.
D. The network connection is too slow to support the required data rate.
Answer: B, C
Question 11.
To speed up file level recoveries, which application information should you use in the client setup?
A. HIST=y and DIRECT=y
B. HIST=y and UPDATE=n
C. HIST=y and DDIMAGE=y
D. HIST=y and UPDATE=y
Answer: A
Question 12.
After rearranging the wiring on ITCertKeys.com's Fibre Channel switch, their Solaris Net Worker storage node cannot see all of its tape devices.
What must you do?
A. verify their Fibre Channel zones do not use ports
B. verify their Fibre Channel ports use arbitrated loops
C. verify the firmware on their Fibre Channel HBA
D. verify the firmware on their Fibre Channel switch
Answer: A
Question 13.
Which of the following facilitates the fastest means of performing a backup of all client file indexes?
A. Create a separate pool for the client file indexes and run a single savegrp command, with an
argument list containing all configured group names.
B. Create a separate pool for the client file indexes and run a savegrp -O for each group.
C. Create a separate pool for the client file indexes and run savegrp for each group.
D. Create a new client for the server, configure a save set list containing the directory of indexes,
put the client in its own group, and back up the group.
Answer: B
Question 14.
Which are three suitable commands or GUIs to configure the use of Microsoft Volume Shadow Copy Service (VSS) save operations? (Choose three.)
A. winworkr.exe
B. nwadmin
C. savegrp -o
D. save -o
E. nwbackup
Answer: A, B, D
|
Question 1.
You believe that there may be a problem with the fault-tolerant VLAN. As a first step, which command would you use to find out if any heartbeats have been missed?
A. ace/admin# show ft stats
B. ace/admin# show ft peer detail
C. ace/context# show ft peer detail
D. ace/context# show ft group detail
Answer: A
Explanation:
Question 2.
Which command could be used to view the configuration stored in a checkpoint?
A. show checkpoint
B. show checkpoint detail
C. show checkpoint config
D. show config checkpoint detail
Answer: A
Explanation:
Question 3.
Where are the checkpoint configuration files stored?
A. Slot0
B. NVRAM
C. TFTP Server
D. a hidden directory in flash
Answer: D
Explanation:
Question 4.
To completely remove a real server from service, you should enter the no inservice command in which mode?
A. Rserver mode
B. privileged mode
C. policy-map mode
D. global config mode
E. severfarm-Rserver mode
Answer: A
Explanation:
Question 5.
Which two of these options are configurable as part of the TCP Normalization feature set? (Choose two.)
A. clearing reserved bits
B. setting illegal flag combinations
C. setting port numbers equal to zero
D. allow Syn packets that contain data
E. setting TCP header length requirements
Answer: A, D
Explanation:
Question 6.
An existing DNS name server is being replaced with a Cisco GSS.
Which IOS license will be required?
A. Cisco Standard license
B. Cisco Extended license
C. Cisco Name Server license
D. Cisco Network Registrar license
Answer: C
Explanation:
Question 7.
An active Cisco ACE Module is configured as follows:
active Cisco Ace Module has priority level of 150
standby Cisco Ace Module has a priority level of 120
probes are configured with host tracking
Two probes fail. What must be done to relinquish the role to the standby Cisco ACE Module?
A. configure the probe with a priority level of 10
B. configure the probe with a priority level of 20
C. configure the probe with a priority level of 40
D. take no action; the Cisco ACE Module automatically relinquishes the role of active on failure of
a probe
Answer: B
Explanation:
Question 8.
Which three fields can be examined by an extended ACL? (Choose three.)
A. TTL value
B. ICMP type
C. IP address
D. HTTP cookie
E. HTTP header
F. UDP port number
Answer: B, C, F
Explanation:
Question 9.
When troubleshooting bridged interfaces, you should start with the show interface VLAN x command.
Which two of these should be true of the interface? (Choose two.)
A. it is up
B. it shows mode : routed
C. it has an IP address and mask
D. it has an MTU set of 1500 bytes
E. it shows Assigned from the Supervisor, up on the Supervisor
Answer: A, E
Explanation:
Question 10.
When migrating from a CSS to a Cisco ACE appliance, you should review hardware resources and identify upgrades and configuration changes required for successful migration.
What is the benefit of doing this?
A. reduces the risks associated with a production migration
B. reduces the possibility of expensive, time-consuming rework at a later date
C. strengthens the ability of your team to meet aggressive deployment schedules
D. reduces the possibility of downtime or other costly disruptions during migration
E. helps take advantage of Cisco planning experience and best-in-class methods and procedures
Answer: A
Explanation:
Question 11.
Which two of these statements are true when using a Cisco ACE Module in a typical routed-mode configuration? (Choose two.)
A. The Cisco ACE Module is assigned only a single VLAN.
B. The Cisco ACE Module is in the path of the client-server traffic.
C. The Cisco ACE Module is out of path of the client-server traffic.
D. The clients and servers are all on the same VLAN, but in different subnets.
E. The Cisco ACE Module's client-side VLAN and the server-side VLAN are separate VLANs on
different subnets.
F. The Cisco ACE Module's client-side VLAN and the server-side VLAN are separate VLANs on
the same subnet.
Answer: A, C
Explanation:
Copyright © 2004 CertsBraindumps.com Inc. All rights reserved.