|
Question 1.
SSH2 on Extreme Networks chipset switches enables encrypted telnet sessions towards the witch. SSH2 Client and Server both have a private key and exchange a public key before the connection is set-up.
A. TRUE
B. FALSE
Answer: A
Question 2.
What are the steps for DVRMP to begin routing multicast packets?
A. Discover neighbor routers => Elect designated browser => exchange route reports
B. Elect designated router => Discover neighbor routers => Exchange route reports
C. Discover neighbor routers => Exchange route report => Elect designated forwarder
D. None of the above
Answer: C
Question 3.
IP Version 6 has amongst other differences with IP Version 4 also different address length.
What is the size of an IPv6 address?
A. 16 bits
B. 32 bits
C. 64 bits
D. 128 bits
Answer: D
Question 4.
Which statement is true about integrated IS-IS.
A. It is a dynamic routing protocol
B. Used to route both IP and OSI packets
C. Supports Pure-IP environments, Pure-OSI and dual environments
D. All of the above
Answer: D
Question 5.
By default OSPF hello packets are sent out every:
A. 2 seconds
B. 10 seconds
C. 30 seconds
D. 40 seconds
Answer: B
Question 6.
Which of the following CLI commands could you use to determine which ports are enabled for ESRP host attach?
A. show ports info detail
B. show esrp detail
C. show esrp
D. show ports config
Answer: B
Question 7.
Dealing with an Access Control List on Extreme switches it's required to include a precedence number when configuring the default rule.
A. TRUE
B. FALSE
Answer: B
Question 8.
What is an IGP protocol other than OSPF that uses the Dijkstrat's SPF routing algorithm?
A. RIP
B. IS-IS
C. EIGRP
D. All of the above
Answer: B
Question 9.
It is possible to set an STP-threshold to switch from a shared tree to a shortest path tree. This switch over will be initiated by:
A. The Rendezvous Point
B. The Bootstrap Router
C. A last hop router
D. The router nearest to the source
Answer: C
Question 10.
Exhibit:
According to accompanying diagram and ACL configuration it is possible for Host A (10.10.10.100) and Host C (30.30.30.100) to successfully communicate.
A. TRUE
B. FALSE
Answer: A
Question 11.
The maximum number of EAPS domains supported per switch and ring is?
A. 64
B. 32
C. 16
D. 8
Answer: A
Question 12.
In Extreme Ware, which one of the following is an optional ESRP configuration that allows you to connect active hosts directly to an ESRP master or standby switch.
A. ESRP Groups
B. ESRP Domain
C. ESRP Host Attach
D. None of these
Answer: C
Question 13.
Which CLI command configures DVMRP on all IP multicast interfaces.
A. config dvmrp add vlan all
B. config dvmrp add all
C. enable dvmrp
D. enable dvmrp vlan all
Answer: A
Question 14.
The following CLI command is valid to advertise SLB virtual servers in OSPF it has a cost of 10. Enable ospf export vip cost 10
A. True
B. False
Answer: A
Question 15.
According to accompanying diagram and ACL configuration it is possible to telnet from host A to any of the switch IP addresses.
A. True
B. False
Answer: B
Question 16.
Extreme Networks IS? Chipset switches allows you to run simultaneously the Radius and Tacacs + features.
A. True
B. False
Answer: B
Question 17.
OSPF requires that all areas attach directly to the backbone area, and that all attachments are made with a direct physical connection.
A. True
B. False
Answer: B
Question 18.
An Ethernet Automatic Protection Switching (EAPS) domain relies on a control VLAN. The ports in that control VLAN ports must be tagged and participating in the ring only.
A. True
B. False
Answer: A
Question 19.
In SLB, Port Translation Mode is similar to Translation Mode, except that in Port Translation Mode the physical Port where the node connects to must be configured as a Fast Ethernet Half Duplex port.
A. True
B. False
Answer: B
Question 20.
In PIM sparse mode the Bootstrap Router election is based on the highest IP address.
A. True
B. False
Answer: B
Question 21
ESRP-enabled switches can utilize either an IP address or an IPX net ID for their protected VLANs.
A. TRUE
B. FALSE
Answer: A
Question 22.
An IP-only IS-IS router (or "IP-only" router) is defined to be
A. A router which uses IS-IS as the routing protocol for IP
B. Does not otherwise support OSI protocols
C. One of the IS-IS router types
D. All of the above
Answer: D
Question 23.
On an Extreme Networks switch, how many bits comprise an OSPF area ID?
A. 32 BITS
B. 48 BITS
C. 64 BITS
D. 128 BITS
Answer: A
Question 24.
What is the RP-set?
A. It is the information of which RP are available for what Multicast groups. It is send by the BSR
towards all PIM routers
B. It is the information of which multicast groups are active It is send by the RP towards all PIM
routers
C. It is the information of which BSR are available for what Multicast groups. It is send by RP
towards all PIM routers
D. It is the information, stored by all RP, needed to find the BSR,
Answer: A
Question 25.
The majority of Extreme Networks switches have a dedicated out of band management port and LAN. The 10/100BASE-TX Ethernet management port allows you to communicate directly to the CPU of the switch. If you want the switch to forward traffic from the mgmt VLAN to other VLANS you just have to enable ip forwarding on all VLANS including the management VLAN.
A. TRUE
B. FALSE
Answer: B
|
Question 1. The abbreviation "VSWR" stands for ___. A. Variable Signal Wave Radio B. Voltage Strength Wire Ratio C. Very Strong Wave Radio D. Voltage Standing Wave Ratio Answer: D Question 2. What is the proper resistance of an ESD wrist strap? A. 1 ohm(O) B. 1 Mega ohm (MO) C. 10 O D. 1 MO Answer: B Question 3. In OMT, what view shows the RUs installed in the GSM cabinet? A. System View B. Radio view C. MO View D. Cabinet View Answer: D Question 4. What could a flashing green LED indicate in an MPU? A. Fault is localized B. Wait, activity in progress C. Battery Power depleted D. None of the above Answer: B Question 5. What common LED indicators are in the CDU, PSU, BFU, and dTRU? A. RBS Fault B. Operational C. Fault D. B and C Answer: D Question 6. How many T1s can one DXU-21 support? A. 1 B. 2 C. 3 D. 4 Answer: D Question 7. An ESD wrist strap must always be used when handling or installing_____. A. a DXU B. printed circuit boards C. TRU/dTRU D. All of the above Answer: D Question 8. Bends to RF cables (coaxial) should be a minimum often (10) times the cable diameter. A. RLSTC:CELL=12002B, STATE=HALTED; B. RLSTC:SITE=12002,STATE=HALTED; C. RLSTP:CELL=12002B, HALTED, D. RLSTP:CELL=12002B, STATE=HALTED; Answer: A Question 9. The abbreviation "COD" stands for_____ A. Command Document B. Command Description C. Command On Demand D. None of the above Answer: B Question 10. In OMT, the System View shows: A. BSC, PCM link, Alarm Inlets, RBS, OMT, ISP, and ESB B. BTS, PCM link, Alarm Inlets, RBS, OMT, IDB, and ESI C. BSC, PCM link, Alarm Inlets, RBS, OMT, IDB, and ETS D. BSC, PCM link, Alarm Inlets, RBS, OMT, IDB, and ESB Answer: D Question 11. If VSWR supervision is disabled in the IDB, an alarm is sent to the BSC if the level reaches_____ A. 1.8 B. 2.2 C. 2.8 D. The alarm is not sent to the BSC Answer: D Question 12. What type of RU is a fan? A. MCRU B. DDMRU C. Subordinate D. Passive Answer: D
Copyright © 2004 CertsBraindumps.com Inc. All rights reserved.