Question 1.
What is the best practice of configuring an intercom on a shared line?

A. This feature allows all endpoints to participate in intercom messages.
B. This feature can be used only when the intercomephone-dn is configured as a dual line
C. This feature is not supported and should not be used
D. This feature can be supported only in a unidirectional manner.
E. This feature allows one endpoint to contact multiple endpoints simultaneously

Answer: C

Question 2.
Using the show ccn trigger command provides the following output:cue-10-0-0# show ccn trigger Name: 
6800Type: SIPApplication: voicemailLocale:en_US Idle Timeout: 5000Enabled: yes Maximum number of sessions: 8Name: 6700Type: SIPApplication: autoattendant Locale:en_US Idle Timeout: 5000Enabled: yes
Maximum number of sessions: 8cue-10-0-0# 

What two pieces of information can you derive from this output? (Choose two.)

A. The number of ports available is 16
B. The operator can bereachedat extension6800
C. The voice-mail pilot point number is 6800
D. The voice-mail application is enabled.
E. The idle timeout is 5 seconds

Answer: C, D

Question 3.
You work as an administrator at your company. You study the exhibit carefully. 

What type of calls can the ephone with extension 2151 make?
Exhibit:
 


A. No impact on out going calls. However, in coming calls will not be permitted to extension 
    2151unless cor list is configured on the ephone-dn
B. Only US calls
C. All calls
D. Internal and emergency calls only, because of the defaultcor restriction.
E. None

Answer: C

Question 4.
You work as an administrator at your company. You study the exhibit carefully. A user at Acme Co. reports that when some one leaves a voice-mail message, their MWI does not light up. The administrator has checked the MWI configuration in Cisco Unified Communications Manager Express and found that the MWI On number is 9001 and the MWI Off number is 9000. 

Using the trace output from the Cisco Unity Express module, what is the problem?
Exhibit:
 

A. The MWI On number configuration is incorrect in Cisco Unity Express
B. The CCN subsystem SIP is incorrect in Cisco Unity Express.
C. The MWI Off Number configuration is incorrect in Cisco Unity Express
D. The SIP is misconfigured in Cisco Unified Communications Manager Express
E. The MWI application is not enabled

Answer: A

Question 5.
You work as an administrator at your company. You study the exhibits carefully. This proposed configuration is meant to forward calls to extension 9999 when extension 2001is busy. 

Which configuration command will most likely to be edited for this to function properly?
Exhibit #1:
 

Exhibit #2:
 

A. max registrations
B. id network mask
C. mailbox
D. voiceregisterpool

Answer: D

Question 6.
You work as an administrator at Your company. You study the exhibit carefully. When two separate calls, FXO and PRI, arrive at the following Cisco Unified Communications Manager Express router, which statement about call behavior is true?
Exhibit:
 

A. The PRI call matches dial-peer50pots, the FXO call matchesdial-peer123pots, and both calls 
    succeed.
B. The FXO call matches dial-peer50pots,the PRI call matches dial-peer123pots,andbothcalls 
    succeed
C. The FXO call matches dial-peer50pots, and the PRI call matchesdial-peer123pots, but both 
    calls fail due to misconfiguration
D. The FXO call matches dial-peer50pots and succeeds, and the PRI call matchesdial 
    -peer123pots , but it fails due to a missing port statement.
E. The PRI call matches dial-peer50pots and succeeds, and the FXO call matchesdial-
    peer123pots , but it fails due to a missing port statement.

Answer: B

Question 7.
You work as an administrator at Your company. You study the exhibit carefully. When a message is left at extensionephone-dn1, the message is left successfully, however the MWI light does not come on. 

Which configuration command resolves this issue?
Exhibit:
 

A. The command MWI SIP is missing underephone-dn 1.
B. The command MWI SIP is missing under voiceregisterpool 1
C. Must configure two ephone-dns for MWI on andMWI off
D. The command MWI is missing under voice register global
E. The command MWI is missing under ephone-dn1

Answer: A

Question 8.
You work as an administrator at Your company. You study the exhibit carefully. Cisco Unity Express is not registered to a Cisco Unified Messaging Gateway. 

What is causing this condition?
Exhibit:
 

A. Email domains are not on the same subnet.
B. Local location ID should be changed to be "10"
C. Cisco Unified Messaging Gateway location is not defined
D. The messaging- gateway registration command is not configured
E. VoiceView cannot be enabled.

Answer: D

Question 9.
You work as an administrator at Your company. You study the exhibit carefully. 

Which command can be used to override all the blocked patterns in the after-hours configuration?
Exhibit:
 


A. Configure the pin command under theephone command
B. Configure the after- hours exempt and pin commands under theephone-dn command
C. Configure the after- hours exempt command under theephone-dn command
D. Configure thenoafter-hours block pattern command under the ephone command.

Answer: C

Question 10.
Which pre configuration task is necessary for VoiceView Express?

A. Ensure that all phones that are owned by the JTAPI user point to the authentication server 
    URL on Cisco Unity Express.
B. Ensure that the authentication server URL points to Cisco Unity Express
C. Ensure that all phones point to the authentication server URL owned by Cisco Unity Express
D. Ensure that authentication server is owned by the JTAPI user on Cisco Unity Express

Answer: B

Question 11.
Which port type must be connected to the fax device for the Cisco Unified Communications Manager Express to support fax pass -through, T.38, and Cisco fax relay?

A. ATA
B. FXS
C. FXO
D. FAX

Answer: B

Question 12.
You work as an administrator at Your company. You study the exhibit carefully. The transcoder is not active and is not registered with Cisco Unified Communications Manager Express. 

Which three commands must be edited or added to for the transcoder to register properly with Cisco Unified Communications Manager Express? (Choose three.)
Exhibit:
 

A. Change maximum session 4 to maximum session 8 to support four different codec types
B. Change associate applicationsccp to associate application transcoder
C. Change associateccm 3 priority 1 to associate ccm 1priority 1.
D. Edit the associate profile 5 register XCDSP1 command to be associate profile 6 register 
     XCDSP1
E. Adddsp services dspfarm under voice-card 0
F. Add thedsp services dspfarm command to sccp ccm group 8

Answer: C, D, E

	Web www.certsbraindumps.com