|
Question 1.
When the Ethernet port of a Cisco MDS 9000 family Port Analyzer Adapter is configured in 1 Gbps mode, what is the state of the LED that is associated with that mode?
A. green
B. amber
C. blinking green
D. off
Answer: D
Question 2.
If you move a licensed Supervisor Module from one MDS Director Switch to another, what is the impact in the new switch environment?
A. The current license will work in either Supervisor slot in the other switch.
B. The current license will not work.
C. The current license will work as long as the Supervisor Module is placed in the same slot as it
was in the previous switch.
D. The current license will work, however, a switch reload is required.
Answer: B
Question 3.
For comprehensive and detailed trend analysis, which two elements are required? (Choose two)
A. Cisco Traffic Analyzer
B. Cisco Resource Manager Essentials
C. Cisco Data Collection Engine
D. Cisco Port Analyzer Adapter
E. Cisco Traffic Collector
Answer: A, D
Question 4.
What three steps must you complete before configuring Inter-VSAN Routing? (Choose three)
A. Enable a routing protocol.
B. Configure unique domain IDs across all VSANs and switches used in IVR operations.
C. Configure IVR only on relevant border switches.
D. Obtain an enterprise license package.
E. Enable FSPF.
Answer: B, C, D
Question 5.
In Fabric Manager. the storage administrator sees a red line through one of the switches in the map.
What two things can the administrator do to troubleshoot the error alert? (Choose two)
A. Verify that one of the power supplies of the switch has not failed.
B. Use the Zone Wizard to create valid zones for switch participation.
C. Execute the fcping command to verify that Fibre Channel connectivity exists between the
nodes and the fabric.
D. Verify that all switch modules are plugged in and are on line.
Answer: A, D
Question 6.
Which three characteristics does an SD port have? (Choose three)
A. It ignores buffer-to-buffer credits.
B. It allows data traffic in the egress (tx) and igress (rx) directions.
C. It does not require a device or an analyzer to be physically connected.
D. Port mode cannot be changed if it is being used for a SPAN session.
Answer: A, C, D
Question 7.
Which three command options does Call Home support? (Choose three)
A. XML-destination
B. HTML-destination
C. short-txt-destination
D. full-txt-destination
Answer: A, C, D
Question 8.
Exhibit:
In the output of the shown interface command, which two statements are correct? (Choose two)
A. This is a Fibre Channel port running at 2 Gbps.
B. This port cannot be attached to any device.
C. This port is in slot 11 in the switch.
D. This port is in multiple VSANs.
E. This port mode is specified to MDS 9000 switches.
Answer: B, E
Question 9.
Which command is used to display the list of hosts configured for Fabric Analyzer remote capture?
A. show fcanalyzer
B. clear fcanalyzer
C. show remote fcanalyzer
D. show fcanalyzer remote list
Answer: A
Question 10.
When using interop mode on an MDS 9000 switch, what is the Domain ID range?
A. 1 to 97
B. 127 to 239
C. 97 to 239
D. 97 to 127
E. 1 to 127
Answer: D
Question 11.
An administrator finds these lines in the running configuration file:
interface vsan1
ip address 10.10.10.3 255.255.255.0
no shut What is the impact of this entry?
A. The entry sets the IP address on the management port and places it in VSAN 1.
B. The entry creates an interface for IPFC.
C. The entry sets up a common IP address to be shared by all Gig E ports in VSAN 1.
D. The entry sets up a default gateway for VSAN 1.
Answer: B
Question 12.
Which three of these upper-level protocols are supported by FC-4? (Choose three.)
A. HIPPI
B. SBCCS
C. OSPF
D. SCSI
E. PPTP
F. CDP
Answer: A, B, D
Question 13.
Which two of these items are advantages of configuring static domain IDs? (Choose two.)
A. facilitates troubleshooting
B. reduces FSPF link-state updates
C. increases switch throughput
D. ensures that persistent FCIDs will not change
E. enables LUN masking
Answer: A, D
Question 14.
You have been asked to install a Cisco MDS switch for Companyxyz.com. If you accept all installation defaults, which of these will occur?
A. default port state: shut default zone policy: deny
B. default port state: no shut default zone policy: deny
C. default port state: shut default zone policy: permit
D. default port state: no shut default zone policy: permit
Answer: A
Question 15.
What are four valid protocols for copying software to the MDS 9000 family switches?
(Choose four.)
A. Remote Copy Service
B. Secure Copy Protocol
C. Trivial File Transfer Protocol
D. File Transfer Protocol
E. Secure Trivial File Transfer Protocol
F. Secure File Transfer Protocol
Answer: B, C, D, F
Question 16.
Which three CLI commands can be used to view remaining buffer-to-buffer credits?
(Choose three.)
A. show interface fc x/y
B. show interface fc x/y brief
C. show interface fc x/y counters
D. show interface fc x/y bbcredit
E. show interface fc x/y flow-control
Answer: A, C, D
|
Question 1.
With Cisco WAAS advanced compression DRE, which three functions are performed during the DRE process? (Choose three.)
A. Pattern matching
B. Synchronization
C. LZ compression
D. Fingerprint and chunk identification
Answer: A, B, D
Question 2.
Do you know how often the Cisco WAAS automatic discovery takes place?
A. Once per user
B. Every hour
C. On a Connection-by-Connection basis
D. Once per office
Answer: C
Question 3.
What is the status of Cisco WAAS optimization after completing the quick start process on all devices and installing the enterprise license? (Choose two.)
A. Cisco WAAS is ready for the Central Manager to be configured to optimized traffic
B. Cisco WAAS is ready for bandwidth settings to be defined for communication
C. Cisco WAAS application optimizers are enabled
D. Default optimizations are applied traffic passing through the Cisco WAE devices
Answer: C, D
Question 4.
Which two statements describe what is required for read-only disconnected mode to be automatically activated during a prolonged WAAS disconnect? (Choose two.)
A. The WAE must be configured for Windows Authentication
B. The Windows server must be configured for operating in disconnected mode
C. The WAE must be able to access a Window Domain Controller
D. The WAE must be joined to the same workgroup as the Windows Server
Answer: A, C
Question 5.
Which three are high-availability Cisco WAE solutions for a branch office? (Choose three.)
A. PBR
B. WCCP
C. Multiple Cisco WAE devices with inline cards
D. Firewall load-balancing Cisco WAE devices
Answer: A, B, C
Question 6
The Cisco WAAS design of your customer calls for the Central Manager to be deployed on the Core WAE, which is a WAE-612 with 2 GB of RAM. The customer initially configured the WAE as an application accelerator and then issued the device mode central-manager command to enable Central Manager Service.
Now the customer complains that the WAE is no longer accelerating traffic why?
A. The Central Manager and application accelerator cannot be deployed on the same WAE
B. The device mode central-manager command must be issued before the device mode
application-accelerator command
C. At least 4 GB of RAM must be installed for the WAE to serve as both Central Manager and
application accelerator
D. Central Manager is consuming too much CPU time on the WAE. The Central Manager service
should be implemented on a less-utilized edge WAE
Answer: A
Question 7.
Which two benefits can we get by using Cisco WAAS with Cisco security devices such as Cisco PIX, Cisco ASA and Cisco IOS Firewalls? (Choose two.)
A. The security devices will speed Cisco WAAS transport
B. The security devices support the TCP sequence number jump that Cisco WAAS uses
C. Cisco WASS requires Cisco Security devices to be installed
D. The security devices can be configured to support Cisco WAAS automatic discovery
Answer: B, D
Question 8.
In Order to ensure Cisco WAAS Mobile transport and management, which three protocols and ports need to be allowed through corporate firewalls? (Choose three.)
A. TCP 80
B. TCP 8080
C. UDP 8080
D. UDP 1182
Answer: A, B, D
Question 9.
SACK improves performance for which type of traffic?
A. Short-lived TCP connections
B. Traffic on high-BDP networks
C. Traffic on lossy networks
D. Traffic on low-BDP networks
Answer: C
Question 10.
Which parameter should be taken into consideration while selecting a Cisco WAE model for a Cisco WAAS deployment?
A. Bandwidth of the largest WAN Link
B. Total WAN throughput
C. Concurrent TCP sessions to be optimized
D. Bandwidth of the smallest WAN link
Answer: C
Copyright © 2004 CertsBraindumps.com Inc. All rights reserved.