|
Question 1. Which tools can you use to upgrade the firmware of the hard drives in a ProLiant server? Select TWO. A. Options Rom Paq B. Version Control Repository Manager C. Firmware CD D. Version Control Agent E. HP Systems Insight Manager Answer: A, C Question 2. Which tool is used to deploy a smart component to a ProLiant server? A. Version Control Repository Manager B. Smart Deployment Utility C. Remote Deployment Utility D. Smart Start Answer: C Question 3. A ProLiant server has an array with four hard drives configured as a RAID 1+0, which holds all the user data. What is the best approach to increase the available space without adding a hard drive? A. Back up all data, delete the existing logical drive, reconfigure to a RAID 5 and restore all data B. Back up all data, migrate the existing RAID 1+0 to a RAID 5 configuration C. Migrate the existing RAID 1+0 to a RAID 5 configuration D. Back up all data, migrate the stripe size, and restore all data Answer: B Question 4. Where should you install a ProLiant server that will hold the confidential data of a new project? A. in the demilitarized zone (DMZ) B. in the Intranet zone, behind the firewall C. in the Internet zone, in front of the firewall D. in the Internet zone Answer: B Question 5. ITCertKeys.com with a Windows 2003 server wants to have the fastest restore possible with the least amount of tapes. Which backup scheme should you advise? A. normal backup every day of the week B. incremental backup on Monday, differential on all other days C. normal backup on Monday, differential on all other days D. copy backup every day of the week Answer: C Question 6. What is a correct statement on backing up to a local disk device? Select TWO. A. Backing up locally keeps traffic off the LAN. B. Backing up locally enables users to share disk devices. C. Backing up locally can be faster than backup over the LAN. D. Backing up locally is an effective means to protect enterprise data. Answer: A, C Question 7. You have a server with redundant power supplies. You remove a power cord from the server and ten minutes later you receive a phone call from HP asking you if you need a new power supply for the server. Which HP solution is installed on this Server? A. Instant Support Enterprise Edition (ISEE) B. HP Systems Insight Manager C. HP Care Pack D. HP System Management homepage Answer: A Question 8. Stephanie is concerned about the down time of the production server. She wants to be certain that in case of a failure, the server is up and running in a minimum amount of time. Which HP solution should you suggest? A. OARS subscription B. basic warranty C. direct access to 2nd level support D. HP Care Pack Answer: D Question 9. You need technical information about a ProLiant 1600 server. Which HP tool should you consult? A. Onsite Agents Reference Set (OARS) B. ProLiant Essentials C. HP Part Reference Guide D. HP Smart Start Answer: A Question 10. Tom ordered a new ProLiant server and would like to have someone install it in a rack. Which HP solution should you suggest? A. Extended Installation Services B. HP Care Pack C. HP Services D. HP Rack Builder Pro Answer: B Question 11. You would like to take advantage of the pre-failure warranty. Which HP tool automates this feature? A. HP Systems Insight Manager B. HP System Management Homepage C. ProLiant Essentials D. Version Control Agent Answer: A Question 12. Which statement is true about the ProLiant DL line of servers? A. They are optimized for maximum expansion B. They are ultra dense servers optimized for rapid deployment C. They are available in rack and tower models D. They are density optimized for rack mount environments Answer: D Question 13. Which ProLiant server lines support AMD processors? (Choose two) A. MSA Line B. BL Line C. CL Line D. XL Line E. DL Line Answer: B, E Question 14. Which statement is true about Serial ATA (SATA)? A. SATA is backward compatible with Parallel ATA (PATA) B. SATA connectors are wider than PATA connectors C. SATA offers hot-plug capability D. SATA requires a terminator at each end of the bus Answer: C Question 15. Which task can you perform using the Option ROM Configuration for Arrays (ORCA) Utility? A. Change the stripe size B. Change the RAID level C. Assign online spare drive D. Expand the logical drive Answer: C Question 16. You want to update the firmware on an HP server console switch. How is the software transferred to the switch? A. Through a serial cable B. Through the on-screen display (OSD) C. Through the IP console view D. Through Trivial File Transfer Protocol (TFTP) Answer: A Question 17. Yon configure a ProLiant server with NIC teaming for fault tolerance. How can you check the functionality of the team? A. Ping 127.0.0.1 B. Remove a network cable from one of the NICs C. Check the properties of the NIC drivers in the Device Manager D. Use the net stat -r command Answer: B Question 18. Where do you enable Advanced Memory Protection? A. ROM-Based Setup Utility (RBSU) B. Array Configuration Utility (ACU) C. Smart Start D. Management CD Answer: A Question 19. ITCertKeys.com wants to upgrade the processor in a ProLiant server to meet performance needs. What must you do before replacing the existing processor? A. Flash the system ROM B. Remove all PPM modules C. Ensure that the server is connected to the UPS D. Check the position of the jumpers an the processor board Answer: A Question 20. ITCertKeys.com is experiencing problems with a storage subsystem. What is the best tool to identify problems with the Smart Array Controller and the installed hard drives? A. Insight Diagnostic Offline Edition B. Flexible Array Storage TooI (FAST) C. Array Diagnostic Utility (ADU) D. Array Configuration Utility (ACU) Answer: C
|
Question 1.
A client needs more disk space for another volume group and has decided to use hdisk12 from the uservg volume group containing hdisk10, hdisk11, and hdisk12 where hdisk10 and hdisk11 have sufficient PPs to contain the volume group data. The client attempted to remove hdisk12 from the volume group but received the following error:
0516-016 Cannot delete physical volume with allocated partitions.
Which of the following commands should be run to correct this problem?
A. reducevg hdisk12
B. rmdev -dl hdisk12
C. cplv hdisk10 hdisk12
D. migratepv hdisk12 hdisk10
Answer: D
Question 2.
A System p administrator is looking at changing attributes of a logical volume.
Which of the following must be defined when it is created?
A. placement of the logical volume
B. stripe size of the logical volume
C. inter-disk policy of the logical volume
D. intra-disk policy of the logical volume
Answer: B
Question 3.
A System p distribution customer is very concerned about Reliability, Availability and Serviceability (RAS). They are planning to install several p6 servers in their facilities and want to be able to move an LPAR from one System p to another.
Which of the following would accomplish this?
A. System p servers using similar SAN storage
B. System p servers must share an HMC
C. System p servers must have the same level HMC
D. System p servers with VIOS
Answer: B
Question 4.
A System p administrator has determined that a recently applied APAR needs to be removed.
Which of the following installp options will remove the APAR?
A. cleanup
B. uninstall
C. deinstall
D. reject
Answer: D
Question 5.
Which of the following actions will enable 64-bit applications on a system with a 32-bit kernel?
A. Use "smit load64bit" to enable the 64-bit applications.
B. Re-install all applications with 64-bit versions.
C. Re-install the OS with 64-bit kernel enabled.
D. Change the kernel to 64bit, reboot, and then use the following command: chdev -l sys0 –a
"applications=64_bit"
Answer: A
Question 6.
A System p administrator needs to document system changes that have occurred recently. The company has a policy of making all possible changes via the smit interface.
Which of the following files would show the commands that have been performed from within smit and their resulting output?
A. /smit.log
B. /smit.script
C. /var/log/smit.log
D. /.history
Answer: A
Question 7.
For security reasons, an administrator is asked to modify the system to prevent someone from leaving a terminal logged in.
Which of the following options would enable a five minute timeout for all users?
A. Add the following line to /etc/environment:
TMOUT=300
B. Add the following lines to /.profile
TMOUT=5
export TMOUT
C. Run the following command:
chuser -u ALL -a TIMEOUT=5M
D. Run the following command:
chsec -u ALL -a TIMEOUT=600
Answer: A
Question 8.
A System p administrator found a process on the server that should be stopped.
Which of the following commands can be used to list all the signal actions defined for this process?
A. ps
B. pstat
C. lssig
D. procsig
Answer: D
Question 9.
A System p administrator has created a customized security profile using AIX Security Expert.
Which of the following commands will apply this to a system?
A. aixpert -f mysec.xml
B. aixpert -a mysec.xml
C. chsec -f mysec.xml
D. chsec -a mysec.xml
Answer: A
Question 10.
How can an administrator determine how many physical copies there are of a mirrored logical volume in rootvg?
A. lslv rootvg
B. lsvg rootvg
C. lsvg rootvg
D. lspv hdisk0
Answer: C
Copyright © 2004 CertsBraindumps.com Inc. All rights reserved.