Question 1.
DRAG DROP
Drag the definition of the resource on the left to the media resource type on the right No1 all media resources are used.
 

Drag and drop question. Drag the items to the proper locations.
Drag the definition of the resource on the left to the media resource type on the right No1 all media resources are used.

Answer:
 

Explanation:
 

Drag and drop question. Drag the items to the proper locations.

Question 2.
Which three steps need to be performed on a third party SIP phone device when adding it to Cisco Unified Communications Manager 6.0? (Choose three.)

A. Select XML as the method to send the third party SIP phone its configuration file.
B. Add the MAC address of the Cisco Unified Communications Manager server to the SIP phone 
    configuration.
C. Set the directory numbers to match the directory numbers configured in Cisco Unified 
    Communications Manager.
D. Set the digest user ID in the SIP device to match the digest user ID in Cisco Unified 
    Communications Manager.
E. Set the TLS user ID and password in the SIP phone to match the TLS user ID and password in 
    Cisco Unified Communications Manager.
F. Set the proxy address in the SIP phone to match the IP address or fully qualified domain name 
    of Cisco Unified Communications Manager.

Answer: C, E, F

Question 3.
Which two gateway configuration statements are required in order to enable Cisco Unified Communications Manager to control a T1 PRI in an MGCP gateway? (Choose two.)

A. mgcp
B. ccm-manager config
C. pri-group configuration on the controller
D. mgcp call-agent pointing to tftp server
E. isdn 13-backhaul ccm-manager on the serial interface
F ccm-manager config server {TFTP ip_address}

Answer: B

Question 4.
DRAG DROP
Click and drag the XML application service information field name on the left to its Answer: description on the right
 

Drag and drop question. Drag the items to the proper locations.
Click and drag the XML application service information field name on the left to its description on the right

Answer:
 

Question 5.
If a service is currently deactivated, how can the service be reactivated from the Cisco Unified Communications Manager Serviceability Control Center page?

A. by clicking on the radio button to the left of the service on theControl Center page
B. by selecting Cisco Unified CM Serviceability > Service Activation and then clicking on the radio 
    button to the left of the service to activate it
C. by selecting Tools > Service Activation, selecting the Answer:server, and clicking on the radio 
    button to the left of the service to activate it
D. by selecting Cisco Unified CM Serviceability > Tools, clicking on the radio button to the left of 
    the service that needs to be activated, and then returning to the Control Center to activate the 
    service

Answer: C

Question 6.
Which two of these media resources are available only in hardware? (Choose two.)

A. trans coding
B. audio conferencing C. MTP
D. annunciator
E. MOH
F. voice termination

Answer: A

Question 7.
DRAG DROP
Click and drag the MoH server parameter on the left to its description on the right. Not all parameters apply.
 

Drag and drop question. Drag the items to the proper locations.

Answer:
 

Explanation:
 

Question 8.
Which three steps are necessary in order to configure DHCP for phone support using the GUI in Cisco Unified Communications Manager 6.0? (Choose three.)

A. add the DHCP server IP address to the device pool
B. activate DHCP Monitor Service
C. add and configure the DHCP server
D. start the application on an external server
E. configure the DHCP subnet
F. download the DHCP server application from the plug-in page

Answer: B, C, E

Question 9.
Which two of these are characteristics of multicast music on hold? (Choose two.)

A. point-to-multipoint, two-way audio stream
B. separate audio stream for each connection
C. multiple audio streams that require multiple multicast IP addresses
D. support for all codecs that are also supported by Cisco Unified Communications Manager 
     servers 
E. conservation of system resources and bandwidth
F. the requirement that there always be a dedicated MOH server

Answer: C

Question 10.
Which three determinations are possible when using the Presence feature in a Cisco Unified Communications network? (Choose three.)

A. Determine if an IP phone has been unplugged if the phone is in the same Cisco Unified 
    Communications cluster as the watcher.
B. Determine if an IP phone is on hook or off hook if the phone is outside the Cisco Unified 
    Communications cluster of the watcher.
C. Determine if an IP phone is on hook or off hook if the phone is in the same Cisco Unified 
    Communications cluster as the watcher.
D. Determine if a set of IP phones is on hook or off hook if the phones are in the same Cisco 
    Unified Communications cluster as the watcher.
E. Determine if an IP phone has been moved or the user has been changed if the phone is in the 
    same Cisco Unified Communications cluster as the watcher.
F. Determine if an IP phone has been off hook beyond a specified period of time if the phone is in 
    the same Cisco Unified Communications cluster as the watcher.

Answer: B, C, D

Question 11.
DRAG DROP
Click and drag the function of the left to the type of barge that it indicates.
 

Drag and drop question. Drag the items to the proper locations.
Click and drag the function of the left to the type of barge that it indicates.

Answer:
 

Explanation:
 

Drag and drop question. Drag the items to the proper locations.

	Web www.certsbraindumps.com