Question 1.
Exhibit:
 

According to the exhibit, R1/BCV on Symm321 and R2 on Symm654 is pair 1, and R1/BCV on Sym654 and R2 on Symm987 is pair 2.

Which of the following commands is utilized for the control SRDF device operations on these two pairs?

A. Symrdf -bcv symrdf brbcv
B. syumrdf symrdf -rbcv
C. Symrdf Jcv symrdf -rdf -bcv
D. Symmir -rdf Jcv symrdf -rbcv

Answer: A

Question 2.
To simultaneously provide Read-Write acc4ess to both the R1 and R2 Volumes of the mydg device group, which SRDF symcli command would be used?

A. symrdf mydg spilt
B. symrdf mydg failover
C. symrdf mydg suspend
D. symrdf mydg spilt -concurrent
E. symrdf mydg suspend - concurrent

Answer: A

Question 3.
You Use Timefinder Snap to issue the following command:
Symnsnap list havedevs

Which two of the following statements best describes the output? (Choose two)

A. Percent full of the active Snap Session is shown.
B. The Symmetrix volumes associated with the Snap Save Devices are listed.
C. Percent full of the Save Devices is shown.
D. Lists the virtual devices associated with the Snap savedev device group.
E. Lists the active Snap Sessions.

Answer: B, C

Question 4.
TimeFinder consistent splits are created by using which two items? (Choose two)

A. Resource Pak
B. Symmetrix integration Utilities (SIU)
C. PowerPath
D. Enginuity Consistency Assist (ECA)
E. Persistent Storage Manager

Answer: C, D

Question 5.
A device group with SRDF source devices would be created by using which of the following SYMCLI commands?

A. symcreate namedg type RDF1
B. symdg create namedg -type RDF1
C. symdg create namedg type REGULAR
D. symdg create namedg type RDF1

Answer: D

Question 6.
DRAG DROP
As an instructor at ITCertKeys.com, you are required to match the correct ECC agents with the tasks on the left, by placing them in the space provided on the right. (NOTE: agents may be used more than once.)
 

Answer:
 

Question 7.
DRAG DROP
For the following, you need to match the Symmetrix device type with the replication technology that it employs. Options may be used more than once.
 

Answer:
             

Question 8.
What are the three features of SRDF/A, if cache and bandwidth are suitably configured? (Choose three)

A. Seconds of data exposure.
B. Unlimited distance.
C. No performance impact.
D. Some performance impact.
E. Hours of data exposure.
F. Limited distance.
G. No data exposure.

Answer: B, C, G

Question 9.
How can the Fibre Channel Buffer Credits, needed for a given distance, be calculated quickly?

A. By multiplying the circuit distance in kilometers by 1.6.
B. By dividing the circuit distance in kilometers by 2.
C. By dividing the circuit distance in miles by 2.
D. By multiplying the circuit distance in kilometers by 2.

Answer: B

Question 10.
Exhibit:
 

In the exhibit above, the SRDF primary mode of operation is Synchronous, there is no secondary mode selected and the SRDF link is ready. While Production work on Host A is in progress, both local mirrors of the R1 Volume fail. 

What will happen in this situation?

A. The Symmetrix will automatically change the status of the R2 Volume to write-enabled and 
    Production work an continue form Host B.
B. Production work can continue from Host A but new write operation cannot be perform.
C. Production work can continue from Host A without interruption. All new writes will accumulate 
    as invalid tracks from the R1 Volume.
D. Product ion work form Host A will fail. The application should be restarted form the Disaster 
    Recovery Host B.

Answer: C

	Web www.certsbraindumps.com