|
Question 1.
What happens when I/O requests are issued to a Vdisk on the non-owning controller?
(Select two.)
A. I/O requests issued have no performance impact.
B. A read request issued has no performance impact.
C. A write request issued has no performance impact.
D. A read request issued has a higher performance impact.
E. A write request issued has a higher performance impact.
Answer: C, D
Question 2.
You connect a 0C6D expansion rack to a fully equipped 2C12D rack.
What is the maximum number of disk drives that can be added to achieve a supported configuration?
A. 56
B. 60
C. 72
D. 84
Answer: C
Question 3.
What causes the first write overhead on an Enterprise Virtual Array?
A. Vraid1
B. Vdisk diagnosis
C. metadata update
D. controller intercommunication
Answer: C
Question 4.
Which component in an EVA4000 subsystem is responsible for bypassing failed disk drives?
A. fibre channel loop switch
B. disk drive enclosure I/O module
C. the Array controller (HSV controller)
D. environmental monitoring unit (EMU)
Answer: B
Question 5.
How many concurrent disk drive failures with an RSS could be covered with a double disk failure protection level?
A. 0
B. 1
C. 2
D. 4
Answer: A
Question 6.
From which page would you display the loop switch property?
A. from the rack property page
B. from the controller property page
C. you can not display the information
D. from the disk enclosure property page
Answer: C
Question 7.
A customer wants to purchase a new Business Copy license for their EVA.
What is the snapshot license policy based on?
A. number of planned snapshots
B. usable capacity of the storage in the EVA
C. usable capacity of the virtual disks replicated
D. usable capacity of the planned snapshots/snapclones
Answer: C
Question 8.
Which attributes are required to create a Vdisk container in Command View EVA? (Select three.)
A. size
B. name
C. spare capacity
D. redundancy level
E. access control list
F. source virtual disk
Answer: A, B, D
Question 9.
Through which interfaces can you enter the storage system name on a new EVA? (Select two.)
A. Command View EVA
B. Operator Control Panel (OCP)
C. Environmental Monitoring Unit (EMU)
D. Replication Solutions Manager (RSM)
E. Storage System Scripting Utility (SSSU)
Answer: A, E
Question 10.
A Vraid5 virtual disk has been created in a 12-member disk group.
What is the result of the loss of one disk?
A. reordering of disks in each RSS
B. reduction in the number of RSSs
C. no change in the number of RSSs
D. addition of a new Redundant Storage Set (RSS)
Answer: B
Question 11.
When presenting a virtual disk to a host in Command View EVA, what will happen if you do not specify a LUN?
A. No LUN is presented to the specified host.
B. All LUNs are presented to the specified host.
C. The next available LUN is presented to the specified host.
D. The most recently selected LUN is presented to the specified host.
Answer: C
Question 12.
Which statements are correct? (Select three.)
A. The EVA4000 contains 2 host ports.
B. The EVA4000 contains 4 host ports.
C. The EVA6000 contains 4 host ports.
D. The EVA6000 contains 8 host ports.
E. The EVA8000 contains 4 host ports.
F. The EVA8000 contains 8 host ports.
Answer: B, C, F
Question 13.
Which arrangement properties describe a robust availability disk group configuration?
(Select three.)
A. The number of disk drive enclosures is odd.
B. The number of disk drive enclosures is even.
C. The member disk drives are arranged in horizontal rows.
D. The member disk drives are arranged in vertical columns.
E. The number of member disk drives is 14 or a multiple of 14 plus 2.
F. The number of member disk drives is equal to or a multiple of the number of disk drive
enclosures.
Answer: B, D, F
Question 14.
You have a disk group that contains 12, 72GB and 12, 146GB disks. The occupancy level of each 72GB disk is approximately 36GB.
What is the approximate occupancy level of each 146GB disk?
A. 36GB
B. 72GB
C. 108GB
D. 145GB
Answer: B
Question 15.
How does EVAPerf store array passwords on the management server?
A. as free text in the Windows registry
B. as encrypted text in the Windows registry
C. as encrypted text in a database located in the EVAPerf install directory
D. as free text in a secure database located in the EVAPerf install directory
Answer: B
Question 16.
You are implementing an EVA6000 2C8D solution at a customer site. The customer needs highest availability and you add disks in groups of eight to the array.
On which property page of Command View EVA can you locate the RSS ID and index information?
A. Vdisk
B. disk enclosure bay
C. disk group, Vdisks tab
D. disk group, general tab
Answer: B
Question 17.
Which statement is correct about the allocation policy of snapshots?
A. If one snapshot in a disk group is created using allocation on demand, all snapshots in the
same disk group must use allocation on demand.
B. If one snapshot in a virtual disk family is created using allocation on demand, other snapshots
in the same virtual disk family can be fully allocated snapshots.
C. If the first snapshot in a virtual disk family is created using the fully allocated method, all
subsequent snapshots in the same disk group must be fully allocated.
D. If the first snapshot in a virtual disk family is created using allocation on demand, all
subsequent snapshots in the same virtual disk family will use allocation on demand.
Answer: D
Question 18.
How does the management server communicate with the HSV controller?
A. using SCSI tagged command queueing commands
B. using Fibre Channel Arbitrated Loop (FC-AL) commands
C. using Storage Management Appliance (SMA) commands
D. using Storage Cell Management Interface (SCMI) commands
Answer: D
|
Question 1.
You work as the network administrator at ABC.com. You are in the process of configuring a Project Server 2010 environment. You have configured two servers. A Windows Server 2008 R2 server named ABC-SQL1 runs SQL Server 2008 R2. A Windows Server 2008 R2 server named ABC-SPS1 runs SharePoint Server 2010 and Project Server 2010.
How can you configure the Project Server 2010 environment to allow Project Web App (PWA) to build OLAP cubes?
A. You need to install the SQL Server 2008 Native Client and Analysis Management Objects on
ABC- SPS1.
B. You need to install the SQL Server 2008 Native Client and Analysis Management Objects on
ABC-SQL1.
C. You need to install SQL Server Analysis Services on ABC- SPS1.
D. You need to configure a trusted data connection library in the Excel Services settings on
ABCSPS1.
Answer: A
Explanation:
Question 2.
You work as the network administrator at ABC.com. Your responsibilities include maintaining the Project Server 2010 environment. The SQL Server 2008 R2 installation on a server named ABC-SQL1 includes the Analysis and Reporting Services. SharePoint Server 2010 and Project Server 2010 are installed on a server named ABC-SPS1. You have been asked by the project manager to enable Project Server reporting.
Which services should you initialize to enable Project Server reporting?
A. You should start the Excel Services Web Service then the Security Token Service.
B. You should start the SQL Server Browser Service the Security Token Service.
C. You should start the Excel Services Web Service then the Secure Store Service.
D. You should start the Security Token Service then the Secure Store Service.
Answer: C
Explanation:
Question 3.
You work as the network administrator at ABC.com. You are in the process of configuring a Project Server 2010 environment. A Windows Server 2008 R2 server named ABC-SQL1 runs SQL Server 2008 R2. You have installed a Windows Server 2008 R2 server named ABC-SPS1. The next step is to install Project Server 2010 on ABC-SPS1. You run the Project Server 2010 installer on ABC-SPS1 but the installation does not complete. You receive an error message on ABC-SPS1 informing you that the server does not meet the minimum software prerequisites.
What is the easiest way to ensure that all the missing software prerequisites are installed?
A. You should install the latest Windows service pack on ABC-SPS1.
B. You should run Windows Update on ABC-SPS1.
C. You should run the SharePoint 2010 Products Preparation Tool on ABC-SPS1.
D. You should select the Complete Installation option in the Project Server 2010 setup.
Answer: C
Explanation:
Question 4.
You work as the network administrator at ABC.com. You are in the process of configuring a Project Server 2010 environment. You have configured two servers. A Windows Server 2008 R2 server named ABC-SQL1 runs SQL Server 2008 and a Windows Server 2008 R2 server named ABC-SPS1 runs SharePoint Server 2010 and Project Server 2010. You need to configure Microsoft SQL Server 2008 Analysis Services to build Project Server 2010 cubes. You log in using the Farm Administrator account and verify that the account has administrative permissions for the Analysis Services on ABC-SQL1.
What should you do next?
A. You should uABCrade Microsoft SQL Server 2008 on ABC-SQL1 to Microsoft SQL Server
2008 R2.
B. You should assign the Farm Administrator account the Sysadmin role on ABC-SQL1.
C. You should add the Farm Administrator account to the local Administrators group on
ABCSPS1.
D. You should delete the Farm Administrator account from OLAP group on ABC-SQL1.
Answer: C
Explanation:
Question 5.
You work as the network administrator at ABC.com. You have been asked to configure a new Project Server 2010 environment. The Project Server 2010 environment will run on multiple virtual servers on the company’s Microsoft HyperV platform.
Which server should you configure first?
A. You should install and configure SQL Server first.
B. You should install and configure Windows SharePoint Services 3.0 first.
C. You should uninstall SharePoint Server 2008 first.
D. You should install and configure Project Server 2007 first.
E. You should install and configure a WINS Server first.
Answer: A
Explanation:
Question 6.
You work as the network administrator at ABC.com. You are in the process of configuring a Project Server 2010 environment. A Windows Server 2008 R2 server named ABC-SPS1 runs SharePoint Server 2010 and Project Server 2010. The database will run on a separate server named ABC-SQL1 running SQL Server 2008.
How should you configure the database to support remote users?
A. You should the SQL Server 2008 Native Client on ABC-SQL1.
B. You should configure ABC-SQL1 to accept desktop remote connections.
C. You should create an exception in Windows Firewall on ABC-SQL1.
D. You should install SQL Server Management Studio (SMSS) on ABC-SPS1.
E. You should configure ABC-SQL1 to accept remote connections using TCP/IP.
Answer: E
Explanation:
Question 7.
You work as the network administrator at ABC.com. Your responsibilities include maintaining the Project Server 2010 environment. You have recently installed the Project Server 2010 environment with the default settings. The Project Server 2010 environment consists of the following two servers. A Windows Server 2008 R2 server named ABC-SQL1 runs SQL Server 2008 R2. A Windows Server 2008 R2 server named ABC-SPS1 runs SharePoint Server 2010 and Project Server 2010. You have been asked to configure a copy of the current environment in a new Project Web App (PWA) instance to be used for testing and training.
What is the easiest way to achieve this goal?
A. You should install a second instance of SQL Server on the ABC-SQL1.
B. You should run SharePoint Central Administration on ABC-SPS1 and configure the names of
the databases to be used using the Project Server service application.
C. You should run SharePoint Central Administration on ABC-SPS1 to configure a new ABC
collection then install the Project Server service application and run the default database
names.
D. You should start the SharePoint 2010 Management Shell on ABC-SPS1 and run the Get-
SPSite -ContentDatabase command.
Answer: B
Explanation:
Question 8.
You work as the network administrator at ABC.com. Your responsibilities include maintaining the Project Server 2010 environment. The Project Server 2010 environment consists of the following two servers. A Windows Server 2008 R2 server named ABC-SQL1 runs SQL Server 2008 R2. A Windows Server 2008 R2 server named ABC-SPS1 runs SharePoint Server 2010 and Project Server 2010. You want to install some Windows Updates on ABC-SPS1. You want to ensure that no data is lost during the update. You also want to disable users’ ability to modify data during the uABCrade to ensure data integrity is maintained.
What should you do before installing the updates?
A. You should use the SQL Server Management Studio to detach the database on ABC-SQL1.
B. You should run the Net Stop W3SVC command on ABC-SPS1.
C. You should run SharePoint Central Administration on ABC-SPS1 and select the Quiesce Farm
option.
D. You should stop the Project Server Queue Service on ABC-SPS1.
Answer: C
Explanation:
Question 9.
You work as the network administrator at ABC.com. Your responsibilities include maintaining the Project Server 2010 environment. The Project Server 2010 environment consists of the following two servers. A Windows Server 2008 R2 server named ABC-SQL1 runs SQL Server 2008 R2. A Windows Server 2008 R2 server named ABC-SPS1 runs SharePoint Server 2010 and Project Server 2010. You are configuring a new laptop for a user named Mia Hamm. Mia will be working on an existing project. You install Project Professional 2010 and configure Mia’s user permissions on ABC-SPS1 to allow her to edit projects using Project Professional.
What should you do to enable Mia to open the project?
A. You should run Project Professional on Mia’s laptop, select the Open Project option and enter
the URL for ABC-SPS1.
B. You should run Project Professional on Mia’s laptop and configure the account settings for
ABC-SPS1.
C. You should run Project Server on ABC-SPS1 and open the project.
D. You should create an account for Mia using SharePoint Central Administration.
Answer: B
Explanation:
Question 10.
You work as the network administrator at ABC.com. You are in the process of configuring a Project Server 2010 environment. The network includes the following two Exchange servers:
ABC-Exch1 runs Exchange Server 2007 R2 and is configured to run the Client Access Server role.
ABC-Exch2 runs Exchange Server 2007 R2 and is configured to run the Mailbox Server role.
You need to configure Project Server 2010 to integrate with the ABC.com Exchange environment.
You have configured the following two servers:
ABC-SQL1 runs SQL Server 2008 R2.
ABC-SPS1 runs SharePoint Server 2010 and Project Server 2010.
You plan to enable task synchronization in Project Web App (PWA).
What should you do first?
A. You should create a user account for ABC-Exch1 in Project Web App (PWA).
B. You should create a user account for ABC-Exch2 in Project Web App (PWA).
C. You should add the computer account for ABC-SPS1 to the Exchange Domain Servers group
in Active Directory.
D. You should add the Farm Administrator’s user account to the local Administrators group on
ABC-Exch1.
E. You should add the Farm Administrator’s user account to the local Administrators group on
ABC-Exch2.
Answer: A
Explanation:
Copyright © 2004 CertsBraindumps.com Inc. All rights reserved.