Question 1.
ITCertKeys.com would like to configure a virtual Ethernet between an AIX V5.3 LPAR and an AIX V5.2 LPAR. 

Which of the following options is necessary to complete this task?

A. Remove the physical Ethernet adapters from the LPARs
B. Activate Advanced POWER Virtualization
C. Update microcode for the virtual adapters
D. Upgrade AIX V5.2 LPAR to AIX V5.3

Answer: D

Question 2.
ITCertKeys.com wants to change the resource allocation for their AIX 5L V5.3 micro LPAR system. 

What is the smallest processor allocation than can be moved between partitions?

A. A full processor
B. 1% of a processor
C. 10% of a processor
D. 25% of a processor

Answer: B

Question 3.
ITCertKeys.com has a p5-570 with an application running on each of three Micro-Partitions. The disk I/O is shared through a VIO server. A technical specialist has been asked to upgrade the VIO server. 

Which of the following procedures should be taken to maintain the integrity of the partitions?

A. Shut down all client partitions before updating the VIO server.
B. Disconnect the client partitions from any IP networks before updating the VIO server.
C. Update the client partitions to the latest OS maintenance level before updating the VIO server.
D. Update the VIO server while the partitions are running, but reboot each client partition at a 
   convenient time after the update.

Answer: A

Question 4.
A technical specialist defined a virtual Ethernet ent2 on the VIO server that has a physical adapter, ent0. 

Which of the following commands should be used to configure the Shared Ethernet Adapter?

A. mkvdev -sea ent2 -vadapter ent0 -default ent0 -defaultid 1
B. mkdev -virtual ent0 -adapter ent3 -default en2 -defaultid 1
C. mkvdev -sea ent0 -vadapter ent2 -default ent2 -defaultid 1
D. mkvdev ent0 -sea -vadapter ent2 -default ent2 -defaultid 1

Answer: C

Question 5.
When planning for a logically partitioned system, which of the following should be used as part of a review to ensure that each partition has the required resources?

A. Use the Workload Estimator capacity planning tool.
B. Use prtconf output from legacy systems.
C. Use the LPAR Validation Tool.
D. Use Performance Management Services.

Answer: C

Question 6.
ITCertKeys.com recently experienced an unanticipated system outage when the VIO server was upgraded. The current p5-570 has six Micro-Partitions and a VIO server partition. 

How can a similar outage be avoided in the future?

A. Use DLPAR to avoid an outage.
B. Deploy a redundant VIO server in the POWER5 system.
C. Add additional Host Bus Adapters and Network adapters to the VIO server.
D. Implement a standby server and move all partitions to it before applying future updates.

Answer: B

Question 7.
When creating a virtual Ethernet adapter on the HMC for a VIO server, what is the advantage of checking the box to access external network (trunk)?

A. Allows the creation of a shared Ethernet adapter
B. Allows the use of VLANs
C. Allows the consolidation of multiple networks on one adapter
D. Allows EtherChannel load balancing

Answer: A

Question 8.
A technical specialist has installed a Host Bus Adapter (HBA) on a p5-550 server. The system has four AIX 5L V5.3 partitions and a Virtual I/O server. The HBA will be used to connect all four partitions to a DS8000 storage array. 

What else must be performed to make the storage available to the partitions?

A. Allocate the HBA to a client partition.
B. Restart the Virtual I/O Server to detect the changes.
C. Install the device driver for the DS8000 in each of the four AIX partitions.
D. Allocate the HBA to the VIO server partition and install necessary drivers.

Answer: D

Question 9.
Which feature of the IBM p5 servers enables customers to be confident that data within two distinct partitions on the server will be isolated?

A. POWER Hypervisor
B. Virtual LAN
C. POWER5 processor
D. Redundant Power and Cooling

Answer: A

Question 10.
ITCertKeys.com wants to reassign a host bus adapter (HBA) from one partition to another to handle increased I/O workload on that partition. 

What needs to be done to dynamically move the card?

A. Use the rmdev command to remove the card from the current partition before doing the 
    DLPAR process.
B. Take the source partition down and do the DLPAR function on the target partition.
C. Assign the card to the required section of the target partition and run cfgmgr.
D. Dynamically remove the card from the source and add to target profile then reactivate the 
    target profile.

Answer: A

	Web www.certsbraindumps.com