|
Question 1. A scripted health check can only contain searches for: A. ASCII content B. Status codes C. Status codes and ASCII content D. Status codes, ASCII content and keep alives Answer: C Question 2. Port profiles are used to define: A. Port types B. Status of ports C. Well known ports D. HTTP health checks Answer: A Question 3. An HTTP health check can return: A. A keepalive B. Status code C. Content verification D. A value to increment the Reassign-Threshold Answer: B, C Question 4. Which of the following Health Check types are performed at Layer 7? A. Arp Request B. TCP C. HTTP D. IMAP4 E. UDP F. LDAP G. MMS H. RSTP Answer: C, D, F, G Question 5. A UDP application is considered down if the server returns: A. No packet B. A garbage packet C. An UDP probe packet D. An ICMP unreachable packet Answer: D Question 6. sFlow is supported on the: A. Server Iron XL B. Server Iron 100 C. Server Iron 400 D. Server Iron 800 E. Server Iron 450 F. Server Iron 850 G. Server Iron GT-E Answer: E, F, G Question 7. SYN-Guard and SYN-Defense can be configured on: A. Server Iron XL B. Server Iron 100 C. Server Iron 400 D. Server Iron 800 E. Server Iron 450 F. Server Iron 850 G. Server Iron GT-E Answer: B, C, D, E, F, G Question 8. An HTTP health check can return: A. A keep alive B. Status code C. Content verification D. A value to increment the Reassign-Threshold Answer: B, C Question 9. Which of the following Health Check types are performed at Layer 7? A. Arp Request B. TCP C. HTTP D. IMAP4 E. UDP F. LDAP G. MMS H. RSTP Answer: C, D, F, G Question 10. How many simultaneous levels of health checks can be configured on the Server Iron to health check the same real server A. Layer 3, Layer4 B. Layer4, Layer7 C. Layer3, Layer4, Layer7, content match D. Layer 4, Layer7, content match Answer: B Question 11. What will be the corresponding Virtual MAC Address belonging to a configured VIP 175.30.15.10 (AF:1E:0F:0A) A. VMACs have to be manually configured B. AF:1E:0F:0A:FF:FF C. 02:0C:DB:1E:0F:0A D. 02:0C:AF:1E:0F:0A Answer: C Question 12. What must be done before a Health-Check Policy will take effect? A. The Health-Check Policy must be bound to the VIP B. The Health-Check Policy intervals and reset must be define C. The Health-Check Policy must be attached to an application port on a real server D. The Health-Check Policy must be configured to use 3-way handshaking Answer: C Question 13. A Matching List can contain: A. Log B. URL C. Down simple D. Status codes E. Up Compound Answer: A, C, E Question 14. When health checking is enabled, a server response time consists of the combination of its response to client requests and its response to Layer 4 or Layer 7 health checks from the Server Iron. A. True B. False Answer: B Question 15. When using a scripted health check, the default health check is disabled. A. True B. False Answer: A
|
Question 1.
Which statement is true about the All-in-One form factor of the HP ap5000 AiO POS System?
A. It is physically smaller than the chassis for the HP rp3000 POS System and HP rp5700 POS
System
B. Its multiple expansion slots allow for greater expandability.
C. It requires only one power cord to turn on the entire unit including integrated peripherals.
D. It includes an integrated monitor and integrated POS keyboard.
Answer: A
Explanation:
Question 2.
Which operating systems include McAfee Total Protection software in the preinstalled image for the HP ap5000 AiO POS System? (Select two.)
A. Microsoft Windows 7 Professional
B. FreeDOS
C. Windows XP Professional downgrade
D. POSReady 2009
Answer: A, C
Reference:
http://h18004.www1.hp.com/products/quickspecs/13540_na/13540_na.html(See Software)
Question 3.
A customer asks where the COM ports are on the HP ap5000 AiO POS System. They are not clearly visible.
Where are they located?
A. behind the cover on the rear panel of the unit
B. on the bottom of the unit, under the pedestal
C. along the side of the resistive touchscreen
D. on the side of the monitor, behind the resistive touchscreen
Answer: A
Reference:
http://h18004.www1.hp.com/products/quickspecs/13540_na/13540_na.pdf(page 5, See the I/O panel layout and the note below it)
Question 4.
After initial setup of the HP ap5000 AiO POS System, a customer reports that the touchscreen monitor is not responding to touch.
What should you tell the customer to do?
A. Make sure the monitor power cable is connected to AC power.
B. Make sure the touchscreen drivers are installed and recalibrate the touchscreen
C. Spray the monitor with the special cleaning solution and gently wipe the surface clean.
D. Check the cable connections between the monitor and the system.
Answer: B
Reference:http://www.manualowl.com/m/Hewlett-Packard/ap5000/Manual/88291?page=33
Question 5.
The optional 26.4-cm (104-inch) Customer Facing Display (CFD) is a replacement for which component of the HP ap5000 AiO POS System?
A. resistive touchscreen
B. non-electronic advertisement panel
C. 2-line display (Vacuum Fluorescent Display-VFD)
D. Multitrack Magnetic Stripe Reader
Answer: C
Explanation:
Question 6.
A customer complains that his touchscreen reads erratically and does not respond to a light touch.
What is a simple solution that might solve the problem?
A. Check the cable connection between the touchscreen and the system.
B. Clean the surface of the touchscreen and recalibrate it.
C. Gently shake the touchscreen to recalibrate the touch receptors.
D. Reboot the machine.
Answer: B
Explanation:
Question 7.
A customer calls and says that the red power LED of the HP ap5000 AiO POS System is blinking nine times.
What does this indicate?
A. The system power is on, but the computer will not boot.
B. Processor thermal protection has been activated
C. A pre-video memory error has occurred.
D. USB ports have failed.
Answer: A
Reference:http://www.manualowl.com/m/Hewlett-Packard/ap5000/Manual/88291?page=39
Question 8.
Which items that are not shipped with the HP ap5000 AiO POS System are required to recover the operating system? (Select two)
A. keyboard
B. flash drive
C. optical drive
D. mouse
Answer: A, C
Explanation:
Question 9.
A customer wants to use a powered USB port but does not know how to locate it.
Which statement is true about the location and appearance of powered USB ports?
A. They are located on the rear I/O panel next to the AC power connector and are aligned
vertically to distinguish them from the regular USB ports.
B. They are located on the rear I/O panel, are specially color coded, and have larger dual
connectors that distinguish them from the regular USB ports.
C. They are located on the front panel under the power button and above the hard drive and
power status LEDs.
D. The ap5000 does not support powered USB ports.
Answer: A
Explanation:
Question 10.
How should a customer respond to a POST memory error message? (Select two.)
A. Press Enter to see more information about the error.
B. Press F1 to ignore the message and continue.
C. Press Ctrl/Alt/Delete to reboot the system
D. Press F10 to correct a system configuration error.
Answer: C
Explanation:
Copyright © 2004 CertsBraindumps.com Inc. All rights reserved.