|
Question 1. Your customer has an Avaya S87xx Server with Communication Manager 4.x and needs to add an additional CLAN card to meet its current traffic load. Which two commands add a CLAN board to the system? (Choose two.) A. addip-interface B. change node-nameip C. add data-module next D. add circuit-pack next E. change communication link Answer: A, B Question 2. What should be configured on Ethernet ports that are connected to IP phones if the Ethernet switch in the Avaya IP telephony system supports spanning tree and port fast features? (Choose two.) A. enable port fast B. disable port fast C. enable port spanning tree D. disable port spanning tree Answer: A, D Question 3. In an Avaya SIP Enabled Services (SES) solution built with an Avaya IP Telephony system, which Communication Manager command should be setup to ensure that a call to a 46xx SIP phone will route to the corresponding SES server user? A. Add station B. Add trunk group C. Add signaling group D. Change off-pbx telephone station-mapping Answer: D Question 4. When defining the network region parameters you can select which RSVP option to use. Which option is best for VoIP? A. reserved-load B. allocated-load C. controlled-load D. guaranteed-services Answer: D Question 5. You are setting up Avaya VoIP Monitoring Manager (VMON) for a customer's Avaya IP telephony system. The default port used by VMON (5005) is already assigned in the network, and so you are assigned another port to use. In which two locations can you change the settings to ensure VMON will work properly? (Choose two.) A. VMON client B. VMON server C. Linux Operation System of the media server D. Avaya Communication Manager of the media server via change system-parametersip-options Answer: B, D Question 6. A customer is using Avaya 4600 Series IP Telephones on an Avaya S87xx Server using several TN799DP (CLAN) and TN2302 (Medpro) cards. One-third of the IP phones reset simultaneously. Now all the telephones are working. Which three commands could you use to begin troubleshooting the problem? (Choose three.) A. list sys-links B. statusip-board resets C. status link X (X represents a communications link number) D. test board XXXXX (XXXXX represents a CLAN board location) E. test board XXXXX (XXXXX represents aMedpro board location) Answer: A, C, D Question 7. What three settings need to be configured on a Layer 2 device? (Choose three.) A. RIP B. port speed C. IP address D. default gateway E. routing interface Answer: B, C, D Question 8. Prior to running a backup procedure, what is the command that needs to be initiated in Communication Manager? A. reset system 4 B. save translations C. list configuration all D. list configuration software Answer: B Question 9. From the Command Line Interface (CLI) of an Avaya S87xx Server, which command verifies that the memory in both servers has been refreshed? A. server B. stat server C. list server D. sh server mem Answer: A Question 10. Your objective is to enable traffic segregation in a particular network region by marking each user's traffic with a VLAN tag. Which field on the Avaya Communication Manager Network Regions screen enables this feature? A. VLAN enabled B. RSVP enabled C. RTCP enabled D. 802.1p/Q enabled Answer: D
|
Question 1. You believe that there may be a problem with the fault-tolerant VLAN. As a first step, which command would you use to find out if any heartbeats have been missed? A. ace/admin# show ft stats B. ace/admin# show ft peer detail C. ace/context# show ft peer detail D. ace/context# show ft group detail Answer: A Explanation: Question 2. Which command could be used to view the configuration stored in a checkpoint? A. show checkpoint B. show checkpoint detail C. show checkpoint config D. show config checkpoint detail Answer: A Explanation: Question 3. Where are the checkpoint configuration files stored? A. Slot0 B. NVRAM C. TFTP Server D. a hidden directory in flash Answer: D Explanation: Question 4. To completely remove a real server from service, you should enter the no inservice command in which mode? A. Rserver mode B. privileged mode C. policy-map mode D. global config mode E. severfarm-Rserver mode Answer: A Explanation: Question 5. Which two of these options are configurable as part of the TCP Normalization feature set? (Choose two.) A. clearing reserved bits B. setting illegal flag combinations C. setting port numbers equal to zero D. allow Syn packets that contain data E. setting TCP header length requirements Answer: A, D Explanation: Question 6. An existing DNS name server is being replaced with a Cisco GSS. Which IOS license will be required? A. Cisco Standard license B. Cisco Extended license C. Cisco Name Server license D. Cisco Network Registrar license Answer: C Explanation: Question 7. An active Cisco ACE Module is configured as follows: active Cisco Ace Module has priority level of 150 standby Cisco Ace Module has a priority level of 120 probes are configured with host tracking Two probes fail. What must be done to relinquish the role to the standby Cisco ACE Module? A. configure the probe with a priority level of 10 B. configure the probe with a priority level of 20 C. configure the probe with a priority level of 40 D. take no action; the Cisco ACE Module automatically relinquishes the role of active on failure of a probe Answer: B Explanation: Question 8. Which three fields can be examined by an extended ACL? (Choose three.) A. TTL value B. ICMP type C. IP address D. HTTP cookie E. HTTP header F. UDP port number Answer: B, C, F Explanation: Question 9. When troubleshooting bridged interfaces, you should start with the show interface VLAN x command. Which two of these should be true of the interface? (Choose two.) A. it is up B. it shows mode : routed C. it has an IP address and mask D. it has an MTU set of 1500 bytes E. it shows Assigned from the Supervisor, up on the Supervisor Answer: A, E Explanation: Question 10. When migrating from a CSS to a Cisco ACE appliance, you should review hardware resources and identify upgrades and configuration changes required for successful migration. What is the benefit of doing this? A. reduces the risks associated with a production migration B. reduces the possibility of expensive, time-consuming rework at a later date C. strengthens the ability of your team to meet aggressive deployment schedules D. reduces the possibility of downtime or other costly disruptions during migration E. helps take advantage of Cisco planning experience and best-in-class methods and procedures Answer: A Explanation:
Copyright © 2004 CertsBraindumps.com Inc. All rights reserved.